Installing Batteries In The Remote Control; Hdd / Dvd / Vcr Modes Switching - FUNAI T3B-N8182DB Owner's Manual

E3B41BD_EN_+nasi.book Page 12 Wednesday, February 7, 2007 6:49 PM
Installing Batteries in the
Remote Control
Install two R6 (AA) batteries (supplied) into the
remote control, carefully match with the polarity
indicated inside the battery compartment.
1
2
Caution
• Incorrect use of batteries can result in hazards such
as leakage and bursting.
• Do not mix new and old batteries together.
• Do not use different kinds of batteries together.
• Make sure that the + and - ends of each battery
match the indications inside the battery
compartment.
• Remove batteries if the equipment will not be used
for a month or more.
• When disposing used batteries, please comply with
governmental regulations or the public instructions
for environmental protection that apply in your
country or area.
• Do not recharge, short-circuit, heat, burn or
disassemble batteries.
About the Remote Control
• Make sure there is no obstacle between the remote
control and the remote control sensor on the unit.
• Use within the operating range and angle as shown.
STA
NDB Y-O
Within about N
7 m
30˚
30˚
Remote control
• The maximum operable range as follows:
Line of sight:
Either side of centre: approximately 5 m within
• Remote control operation may become unreliable if
the remote control sensor of the unit is being
exposed by the strong sunlight or fluorescent light.
• Remote controls for different devices can interfere
with each other. Be careful when using remote
controls for other equipment located close to the
unit.
• Replace the batteries when the operating range of
the remote control reduces.
EN
3
PAL
STO
P/E
JEC T
RE
W
F.F
WD
PL
AY
RE
CO RD
VC R
OP
EN
/ CL
OS E
PR
OG .
DU
VC BB ING
R
DV D
HD D VC R
DV HD D
D
DV D
ST
OP
PL
AY
HDD
REC ORD
DVD
HD
D/ DV
D
S-V
IDE O
VID
EO
L
AU
DIO
R
Within about
5 m
approximately 7 m
30 degrees
HDD / DVD / VCR Modes
Switching
Because this unit is a combination of a VCR, a HDD
and a DVD recorder, you must select first which
component you wish to operate.
Device Select Buttons / Indicators
PAL
OPEN / CLOSE
STANDBY-ON STOP/EJECT REW F.FWD PLAY RECORD DUBBING
PROG. VCR HDD
VCR DVD
VCR HDD DVD
VCR HDD DVD
DVD button / indicator
HDD button / indicator
VCR button / indicator
VCR button
HDD button
DVD button
HDD mode
Press [HDD] on the remote control.
(Verify that the HDD indicator is lit.)
DVD mode
Press [DVD] on the remote control.
(Verify that the DVD indicator is lit.)
VCR mode
Press [VCR] on the remote control.
(Verify that the VCR indicator is lit.)
Note
• If you press [REC] of each device, recording starts
in its device mode.
12
TIMER INPUT OPEN/CLOSE
STANDBY-ON PROG. SELECT EJECT
STOP PLAY HDD RECORD DVD
DVD
S-VIDEO VIDEO AUDIO .@/: ABC DEF
L R
HDD/DVD
PROG.
GHI JKL MNO
SATELLITE
PQRS TUV WXYZ
LINK
CHAPTER
MARK SPACE SYSTEM
TIME
SHIFT SETUP AUDIO CLEAR
DISC MENU TOP MENU
ENTER
DISPLAY RETURN
VARIABLE VARIABLE
SKIP REPLAY SKIP
REV PLAY FWD
STOP
PAUSE VCR HDD DVD
REC MODE REC
1.3x/0.8x
REPEAT SEARCH PLAY DUBBING
MODE SELECT
NB331