Sharp MX-M260 Service Manual page 64

48
48-1
Purpose Adjustment
Function Used to adjust the copy mode magnification ratio
(Purpose) (main scanning direction, sub scanning direction).
Section Image processing
Item Picture quality
Operation/procedure
1. Touch the item to be set.
The item and the currently set value are highlighted.
2. Press the [START] key.
The display is shifted to the copy menu.
3. Select the paper feed tray and the print density, and enter the
adjustment value with the 10-key.
4. Press the [START] key.
Copying is started.
Item
Main scanning magnification
1 F-R
ratio adjustment
Sub scanning magnification
2 SCAN
ratio adjustment
RSPF surface sub scan
3 SPF (SIDE1)
magnification ratio
RSPF back surface sub scan
4 SPF (SIDE2)
magnification ratio
DUPLEX sub scanning
5 DUPLEX
magnification ratio adjustment
Note: When this simulation is canceled, the display is shifted to the ini-
tial menu, but the machine is not reset.
48-2
Purpose Adjustment
Function Used to adjust the scanner mode magnification ratio
(Purpose) (main/sub scanning direction).
Section Image processing
Item Picture quality
Operation/procedure
1. Touch the item to be set.
The item and the currently set value are highlighted.
2. Press the [START] key.
The display is shifted to the copy menu.
3. Select the paper feed tray and the print density, and enter the
adjustment value with the 10-key.
4. Press the [START] key.
Copying is started.
Item Content
Main scanning magnification
1 F-R
ratio adjustment
Sub scanning magnification
2 SCAN
ratio adjustment
RSPF surface sub scan
3 SPF (SIDE1)
magnification ratio
RSPF back surface sub scan
4 SPF (SIDE2)
magnification ratio
Setting
Content Default
range
1-99
Setting
Default
range
1-99
MX-M260/M310/M260N/M310N SIMULATION 6 - 31
48-3
Purpose Adjustment
Function Used to adjust the print mode magnification ratio
(Purpose) correction.
Section Image processing
Item Picture quality
Operation/procedure
1. The adjustment item and the currently set value are highlighted.
2. Enter the adjustment value with the 10-key.
Changes magnification ratio by changing speed of main motor.
The change of the paper transfer speed is 0.1% when changing value
is 1.
Item
1 145mm/s
2 122mm/s
48-8
Purpose
50
Function
(Purpose)
60
Section
Related soft SW
Operation/procedure
1. Select "1: COPY START."
50
The currently set value is highlighted beside the item.
2. Enter the set value of magnification with the 10-key, and press the
[#/P] key.
3. Press the [START] key.
Copying is started and the set value is stored.
Normal display
Error display
There is no operation of tray selection.
The optimum paper tray for the scanned size is selected.
Even when the SPF/RSPF is selected, if there is no original on the
SPF/RSPF, the OC is scanned.
Even when the OC is selected, if there is any original on the SPF/
RSPF, the SPF/RSPF is scanned. (Setting 2)
Item
1 COPY START
SCAN SELECT
2
(OC/SPF/RSPF)
3 OC(MAIN)
4 OC(SUB)
50
5 SPF(MAIN)
6 SPF(SUB)
7 RSPF(MAIN)
8 RSPF(SUB)
Content
Main motor speed (145mm/s)
Main motor speed (122mm/s)
Adjustment
FAX magnification adjustment (read)
FAX
SW112-1 to 8, SW113-1 to 8
NOW PRINTING
DOOR OPEN
JAM
PAPER EMPTY
Content
Copy start
Scan selection
(OC/ SPF/RSPF)
SCAN Main scanning
magnification ratio
adjustment (OC)
SCAN Sub scanning
magnification ratio
adjustment (OC)
SCAN Main scanning
magnification ratio
adjustment (SPF)
SCAN Sub scanning
magnification ratio
adjustment (SPF)
SCAN Main scanning
magnification ratio
adjustment (RSPF)
SCAN Sub scanning
magnification ratio
adjustment (RSPF)
Setting
Default
range
45-55 50
Setting
Default
range
– –
1-255* 128
1-255* 128
1-255* 128
1-255* 128
1-255* 128
1-255* 128
1-255* 128