Sharp MX-M260 Service Manual page 52

26-10
Purpose Setting
Function (Purpose) Network scanner trial mode setting
Section Scanner
Operation/procedure
Enter the set value with the 10-key and press the [START] key.
Item Content
0 END Trail mode cancel
1 START Trial mode start
If the trial scanner counter value is less than 500, the trial mode setting
can be repeatedly made. If the scanner trial counter value is 500 or
more, the trial mode setting cannot be made.
When the scanner is not set and the scanner trial counter value is less
than 500, if "1" is entered in SIM26-10, the trial mode setting is started.
If "0" is entered in SIM26-10, the trial mode setting is canceled.
After recognition of the scanner, the trial mode setting cannot be made.
(Entering "1" is invalid and a beep sound is produced.)
When this setting is made, the machine must be reset after canceling
the simulation. When "1: Trial mode start" is selected, the scanner
function is valid. If "0: Trial mode cancel" is selected, the scanner func-
tion is invalid.
When setting is invalid (when the scanner is recognized or the scanner
trial counter value is 500 or more) in the key operations of the trail
mode setting, an invalid sound (beep sound) is made. In the other
case, a valid sound is made.
* When the scanner trial counter value is changed from 500 or more to
less than 500, the trail setting is changed from "END" to "SETTING
START."
Note: Executable only when the PCL/SCANNER is installed.
26-12
Purpose Setting
Function
Used to input the Software Key for E-MAIL RIC.
(Purpose)
Section E-MAIL RIC
Item Specifications
Operation/procedure
The current setup is displayed with ON or OFF.
Enter an input (20 digits) of the E-MAIL RIC soft key with the 10-key
and press the [START] key, and the collating result is displayed with OK
or NG.
After canceling the simulation, if OK, the E-MAIL RIC function is
enable; if NG, the E-MAIL RIC function is disabled.
This setting must be reset after the simulation cancel.
* If recognition is OK, the E-Mail RIC can be set to Enable. If the FAX
is installed, however, the operation cannot be made actually.
Note: Executable only when the PCL/NIC is installed.
26-14
Purpose Setting
Function
Used to input the Software Key for the PS extention kit.
(Purpose)
Section Printer
Item Specifications
Default
0
MX-M260/M310/M260N/M310N SIMULATION 6 - 19
Operation/procedure
The current setup is displayed with ON or OFF.
Enter an input (20 digits) of the PS expansion kit soft key with the 10-
key and press the [START] key, and the collating result is displayed
with OK or NG.
After canceling the simulation, if OK, the PS expansion kit function is
enable; if NG, the PS expansion kit function is disabled.
This setting must be reset after the simulation cancel.
Note: Executable only when the PCL/PS3 is installed.
26-18
Purpose Setting
Function
Used to set enable/disable of toner save operation.
(Purpose)
Item Specifications
Operation/procedure
Input the set value with the 10-key and press the [START] key.
Item Content
0 OFF Disable
1 ON Enable
Note: Setup is allowed only for Japan and UK.
26-22
Purpose Setting
Function Used to set the specification (language display) for the
(Purpose) destination.
Item Specifications
Operation/procedure
Select the display language with the 10-key, and press the [START]
key.
This setup varies in connection with SIM 26-6 (Destination setup).
Item
0 JAPANESE
1 ENG.US
2 ENG.UK
3 FRENCH
4 GERMAN
5 ITALY
6 DUTCH
7 SWEDISH
8 SPANISH
9 PORTUGUESE
10 TURKISH
11 GREEK
12 POLISH
13 HUNGARIAN
14 CZECH
15 RUSSIAN
16 FINNISH
17 NORWEGIAN
18 DANISH
19 CHINESE
20 TAIWANESE
21 SLOVAK
22 HEBREW
BRAZILIAN
23
PORTUGUESE
24 ARABIC
25 FARSI
Operation mode (Common)
Setting
Default
range
0-1
Remarks
Traditional Chinese supported locally
Supported locally
0