Sharp MX-M260 Service Manual page 54

26-69
Purpose Setting
Function (Purpose) Toner near end setting
Item Operation
Operation/procedure
Item
1 Toner preparation 0: Displayed
message display 1: Not displayed
setting.
2 Toner near end 0: Displayed
massage display 1: Not displayed
setting.
3 Toner end status 1: Operate
operation setting. 2: Operate (However, if
3: Not operate
4 E-mail alert sending 0: When the near near
timing setting.
1: When the near toner
26-71
Purpose Setting
In the power save time setting, the pre-heat (pre-heat
mode setting) and the auto power shut off time can be
Function
set to the short time setup (pre-heat: 1 min, auto power
(Purpose)
shut off: 4 min) and the long time setup (pre-heat:
5min, auto power shut off: 30min).
Operation/procedure
Select the short time setup or the long time setup of the pre-heat time
and the auto power shut off time with the 10-key, and press the
[START] key.
Item Content
1 Preheat: 1min, auto power shut off: 4min
2 Preheat: 5min, auto power shut off: 30min
Note: When the sub code 71 is entered to display the setting menu,the
default values are always displayed. (However,the default time is
not always set.)
26-72
Purpose Setting
The letterhead support is set.
Function When "Letterhead paper setting" is selected, the set
(Purpose) value of SIM 26-46 (Image output direction setting) is
set to "Setting Enable" accordingly.
Operation/procedure
Input the set value with the 10-key and press the [START] key.
Item Content
0 OFF Letterhead paper is not set.
1 ON Letterhead paper is set.
Set value Default
0
0
3
CRUM ID matches, not
operates.)
1
toner end, the toner low
status is sent.
end, the toner low
status is sent.
Default
2
Setting
Default
range
0-1 0
MX-M260/M310/M260N/M310N SIMULATION 6 - 21
27
27-1
Purpose Setting
Function Used to set PC/MODEM communication trouble
(Purpose) (U7-00) detection Yes/No.
Section Communication (RIC/MODEM)
Item Specifications
Operation/procedure
Input the set value with the 10-key and press the [START] key.
Item
In case of the communication trouble, U7-00 is
0 OFF
not displayed.
In case of the communication trouble, U7-00 is
1 ON
displayed.
27-2
Purpose Setting
Sender's registration number/HOST server
Function (Purpose)
TEL number.
Operation/procedure
1. The current setting value is displayed in PRESENT field.
2. Enter the number with 10-key, the setting value is saved and the
display of PRESENT is updated.
27-4
Purpose Setting
Function (Purpose) Function setting
Operation/procedure
Enter the item number of setting with 10-key, press [START] key.
Display Contents
1 RETRY Recall number setting when
BUSY busy (unit: times)
2 TIMER Recall interval setting when
(MINUTES) busy (unit:minute)
BUSY
3 RETRY Recall number setting when
ERROR send error (unit: times)
4 TIMER Recall interval setting when
(MINUTES) send error (unit: minute)
ERROR
5 TONER Toner order
ORDER auto send
TIMING timing setting
6 FAX INIT Retry number setting of initial
RETRY connection (unit: times)
Operation mode (Common)
Content Default
Setting
Default
range
0-5
1-15
0-15
1-15
Empty 0
Near End 1
25% or less 2
0-5
25-49% 3
50-74% 4
75-100% 5
0-15
0
2
3
1
1
3
2