Sharp MX-M260 Service Manual page 47

Panel
Destination Panel software support language
display
SEC
SECL
SUK American English, English, French, Spanish,
EFS
Brazilian Portuguese
SCA/SCNZ
Distributor
area
SEEG/
English, German, Polish, Czech, Hungarian,
SEA/East
EEU Greek, Turkish, Russian, French, Italian,
Europe,
Slovak
etc.
SEF/
English, German, French, Spanish, Dutch,
SEES/
NEU Italian, Portuguese, Swedish, Norwegian,
SEIS/SEN,
Finnish, Danish
etc.
Simplified Chinese, American English,
CHN SOCC
English
Traditional Chinese (Local support),
TWN Taiwan
American English, English
Saudi American English, English, French, Spanish,
ARB
Arabia Hebrew (Local support), Arabic
FAS Iran English, Arabic, Persian
22-6
Adjustment/setting/operation data output/check
Purpose
(display/print)
Function Used to print each key operator setting, the account
(Purpose) information, and the machine adjustment values.
Item Data
Operation/Procedure
(Initial screen)
The currently set value is highlighted beside the adjustment item.
1. Select the adjustment item with the 10-key.
2. Press the [START] key.
The display is shifted to the copy menu and the set value is stored.
3. Select the paper feed tray and the print density.
4. Press the [START] key.
Copying is started. (Printing at 1200dpi cannot be made.)
After canceling a jam (After picking up, the [C] key is invalid.)
When the other information is repeatedly printed, the display may show
the message, "Remove original from original table." However, the oper-
ation is performed normally.
Item
1 ALL All lists group print (Default)
2 KEY OPE Key operator information list
ACCOUNTING
3 List of total number of prints
COUNTERS
4 AUDITOR NO. Department number list
MACHINE SIM
5 Machine simulation setting list
SETTING
FAX simulation setting list (Only when
the FAX board is installed. The display
6 FAX SIM SETTING*1
does not go to the print data transfer
display, but to the FAX SIM menu.)
* When the IMC board is not installed, key input is disabled.
* Duplex print cannot be made.
* For the FAX SIM setting list, the display and the operating proce-
dures differ.
Note: When the simulation is canceled, the display returns to the origi-
nal state but the machine is not reset.
Setting/adjustment data
Content
MX-M260/M310/M260N/M310N SIMULATION 6 - 14
22-7
Purpose User data output/Check (Display/Print)
Function
Used to display of the administrator password.
(Purpose)
Item Data
Operation/procedure
Used to display the administrator password.
22-8
Adjustment/setting/operation data output/check
Purpose
(display/print)
Function
Used to display the original, staple counter.
(Purpose)
Item Counter
Operation/procedure
Each counter is displayed.
SPF RSPF counter
SCAN Scan counter
STAPLE Stapler counter
The counter display is in 7 digits.
22-9
Adjustment/setting/operation data output/check
Purpose
(display/print)
Function Used to check the number of use of each paper feed
(Purpose) section. (the number of prints)
Section Paper feed
Item Counter
Operation/procedure
Used to display each paper feed counter.
BYPASS Manual feed counter
TRAY1 Tray 1 counter
TRAY2 Tray 2 counter
TRAY3 Tray 3 counter
TRAY4 Tray 4 counter
The counter display is in 7 digits.
22-10
Adjustment/setting/operation data output/check
Purpose
(display/print)
Function
Used to check the system configulation.
(Purpose)
Item Specifications
Operation/procedure
The detected machine composition is displayed.
(The job separator cannot be detected. Based on SIM 26-1 setting.)
Item
SPEED 26CPM/31CPM
DF NONE/[1: RSPF]
OUTPUT NONE/[2: Finisher]/[3: Job separator]
CASETTE1 NONE/[4: One-step paper feed unit]
CASETTE2 NONE/[5: Two-step paper feed unit]
IMC MEM NONE/Expansion memory capacity (MB)
PRINTER NONE/[6: PRINTER]
PS3 NONE/[7: PS3]
NIC NONE/[8: NIC]
SCANNER NONE/[9: SCANNER]
FAX NONE/[10: FAX]
FAX MEM NONE/Memory capacity (MB)
HAND SET NONE/[11: Handset]
USB HOST NONE/USB HOST
User data
Option
Display items