Sharp MX-M260 Service Manual page 55

27-5
Purpose Setting
Function (Purpose) Used to set the tag number
Item Data
Operation/procedure
1. The currently set number is displayed on the PRESENT column.
2. Enter the new tag number (Max. 8 digits) with the 10-key.
The entered number is displayed on the NEW column.
3. Press the [START] key.
The set value is stored and "PRESENT" is revised.
27-7
Purpose Setting
Function (Purpose) FSS function setting
Operation/procedure
Enter the item number of setting with 10-key, press [START] key.
Item
1 FUNCTION* 0: FSS function enable
1: FSS function disable (*) (Default)
2 ALERT 0: Alert call enable (Default)
1: Alert call enable
3 CONNECTION 0: FAX connect enable (Default)
1: E-MAIL connect enable
(*) The FSS function setting can be changed only from Disable to
Enable. (Cannot be changed from Enable to Disable.)
27-9
Purpose Setting
Function (Purpose) FSS function adjustment
Operation/procedure
Display Contents
1 FEED TIME1 Sensor distance transport
time (main unit)
2 FEED TIME2 Sensor distance transport
time (RSPF)
3 JAM ALERT Continuous JAM alert
judgment
27-10
Purpose Setting
Function (Purpose) Trouble precognition history clear
Operation/procedure
Target of history that is cleared
• Scan gain retry times history
• Sensor distance paper transport history (main unit/RSPF)
27-14
Purpose Setting
Function (Purpose) FSS connection test setting
Operation/procedure
Input the set value with the 10-key and press the [START] key.
Item
0 OFF FSS connection test disable
1 ON FSS connection test enable
Set value
Setting
Default
range
0-100 50
1-100 10
Content
MX-M260/M310/M260N/M310N SIMULATION 6 - 22
27-15
Purpose Operation test/check
Function (Purpose) Displays status of FSS connection
Operation/procedure
Enter the set value with the 10-key.
Item
0 OFF Not connected
1 ON Connected
30
30-1
Purpose Operation test/check
Function Used to display the sensor status attached to the
(Purpose) machine.
Section Others
Item Operation
Operation/procedure
The active sensors and detectors are highlighted.
PPD1H PS paper detection 1 sensor
PPD1L PS paper detection 2 sensor
PPD2 Fusing paper sensor
POD1 1st paper exit paper out sensor
DVCH Developing cartridge detection sensor
DRST Drum intial detection sensor
DSWR1 Interlock switch (side door)
SFTHP Shifter home position sensor
POD2 2nd paper exit paper out sensor
TOPF 2nd paper exit full detection sensor
DSWR0 2nd paper exit cover open/close detection sensor
LOEMP 1st paper exit empty detection sensor
DUP2 Reverse path paper sensor
POD3 Right paper exit sensor
PTOPF Right paper exit full sensor
30-2
Purpose Operation test/check
Used to display the status of the sensors attached to
Function the standard tray and the manual feed tray. (Use SIM
(Purpose) 4-2 for the option trays.)
The sensor of an uninstalled tray is not displayed.
Section Paper feed
Item Operation
Operation/procedure
The active sensors and detectors are highlighted.
PED1 1st tray paper empty sensor
LUD1 1st tray paper upper limit detection sensor
CD1 1st tray empty sensor
PED2 2nd tray paper empty sensor
LUD2 2nd tray paper upper limit detection sensor
CD2 2nd tray empty sensor
PFD2 2nd tray paper pass sensor
DSWR2 2nd tray right door detection sensor
MPED Manual tray paper empty detection
MPLS1 Manual tray length detection 1
MPLS2 Manual tray length detection 2
MPLD1 Manual feed paper length detection 1
MPLD2 Manual feed paper length detection 2
Width detection size of the manual feed tray (one of them is displayed.)
A4/A3, LT/WLT, B5/B4, INV/LTR, A5/A4R, B5R, POSTCARD, EXTRA,
8K/16K
(At detection, highlighted)
Content