Table of Contents
Advertisement
SLM-7650 Satellite Modem
Remote Control Specifications
Parameter 10:
Parameter 11:
Parameter 12:
Parameter 13:
Parameter 14:
Parameter 15:
Parameter 16:
Parameter 17:
Parameter 18:
Parameter 19:
Parameter 20:
Parameter 21:
Parameter 22:
Parameter 23:
Parameter 24:
Parameter 25:
Parameter 26:
Parameter 27:
Parameter 28:
Parameter 29:
Modulator Spectrum Rotation (ref. "MSR_" command).
P10 = n, where 'n' is '0', '1' (0 = NRM, 1 = INV).
TX IESS-310 Operation (ref. "T310_" command).
P11 = n, where ,n, is '0' or '1' (0 = OFF, 1 = ON).
Transmit clock source (ref. "TC_" command).
P12 = n, where 'n' is (0= INT,2=EXT,6=DATA).
Transmit clock phase (ref. "TCP_" command).
P13 = n, where 'n' is '0', '1', '2' (0 = NRM, 1 = INV, 2 =
AUTO).
Transmit data phase (ref. "TDP_" command).
P14 = n, where 'n' is '0', '1' (0 = NRM, 1 = INV).
Transmit BPSK Data Ordering (ref. "TDA_" command).
P15 = n, where 'n' is '0', '1' (0 = NRM, 1 = INV).
Carrier Only Mode (ref. "COM_" command).
P16 = n, where 'n' is '0' (OFF),'1'(CENTER-CW), '2' (DUAL-
CW), or '3' (OFFSET-CW).
RTS TX-IF Control Mode (ref. "RTSM_" command).
P17 = n, where ,n, is '0' or '1' (0 = OFF, 1 = ON).
Interface substitution pattern (ref. "ISP_" command).
P18 = n, where 'n' is '0' to '2'
(0=OFF,1=2047/ON,2=MIL188).
Transmit data fault (ref. "TDF_" command).
P19 = n, where 'n' is '0', '1' to '2' (0=NONE,1=DATA,2=AIS).
Modulator Power Offset (ref. "MPO_" command).
P20 = snn.n, transmitter output power offset in dBm.
Scrambler Type (ref. "SCRT_" command).
P21 = n where n = '0' (IESS), '1' (OM73), or '2' (TURBO).
SCT PLL Reference (ref. "MSPR_" command).
P22 = n, where 'n' is '0' or '1' (0=MR, 1=ERF)
ASYNC TX Baud Rate (ref. "TOBR_" command).
P23 = n, where: 'n' is '0' = 110 baud,
ASYNC TX Character Length (ref. "TCCL_" command).
P24 = n, where: 'n' is '7' or '8' bits.
ASYNC TX Stop Bits (ref. "TCSB_" command).
P25 = n, where: 'n' is '1' or '2' bits.
ASYNC TX Parity (ref. "TOCP_" command).
P26 = n, where: 'n' is '0' = NONE,
Reserved.
Mod RS Codeword (ref. "MRSC_" command).
P28 = n, where: 'n' is '0' = RS(225,205,10) depth 8,
Interface Coding Format Transmit (ref. "ICFT_"
command).
P29 = n, where 'n' is '0' (AMI), '1' (B6ZS), '2' (B8ZS), or '3'
(HDB3).
A–7
Revision 4
MN/SLM7650.IOM
'1' = 150 baud,
'2' = 300 baud,
'3' = 600 baud,
'4' = 1200 baud,
'5' = 2400 baud,
'6' = 4800 baud,
'7' = 9600 baud,
'8' = 19200 baud,
'9' = 38400 baud
'1' = EVEN,
'2' = ODD
'1' = RS(225,205,10) depth 4,
'2' = RS(219,201,9) depth 8,
'3' = RS(219,201,9) depth 4,
'4' = RS(194,178,8) depth 4,
'5' = RS(126,112,7) depth 4
Advertisement
Table of Contents
