Special Paper Action; Switching Measurement; Error Handling; Function Defaults - Kyocera KM-3050 Service Manual

Special paper action

To print on Prepunched, Preprint, and Letterhead, punch-
holes might fail to be aligned or print direction might be
upside down depending on how to set the originals and
combination of copying functions. In such a case, select
[Adjust Print Direction] to adjust the print direction. When
paper orientation is not important, select [Speed Priority].
1. Press [Next] of Original/Paper Setup and then
[Change] of Special Paper Action.
2. Press [Adjust Print Direction] or [Speed Priority].
3. Press [OK].

Switching measurement

Select inch or metric for the unit for paper dimensions.
1. Press [Change] of Measurement.
2. Press [mm] for metric or [Inch] for inch.
3. Press [OK].

Error handling

Select whether cancelling or continuing the job when
error has occurred.
1. Press [Next] of Error Handling.
2. Press [Change] at the error to change what to do
about it.
Duplexing Paper Error: 1-sided/Display Error
Finishing Paper Error: Ignore/Display Error
No Staple Error: Not Stapling/Error Display
NOTE: The messages are displayed when the
optional document finisher, built-in finisher or 3000-
sheet document finisher is installed.
Stapling Limit Error: No Stapling/Error Display
NOTE: The messages are displayed when the
optional document finisher, built-in finisher or 3000-
sheet document finisher is installed.
Punch Waste Full Error: No punching/Error Display
NOTE: The messages are displayed when the
optional 3000-sheet document finisher and punch
unit are installed.
3. Select what to do about errors and press [OK].
Output tray
Select output tray respectively for copy jobs, print jobs
from Custom Box, computers, and FAX RX data.
NOTE: Optional job separator, document finisher, 3000-
sheet document finisher, and mailbox are required.
FAX RX data output can be specified when the optional
fax kit.
1. Press [Next] of Output Tray.
2. Press [Change] of Copy/Custom Box, Printer, or
FAX.
3. Select Output Tray.
Top Tray/Finisher Tray/Tray A/Tray B/Tray C/Job
Separator/Tray 1-7
For [Finisher Tray], [Tray B], [Tray C] or [Tray 1-7],
select [Face Up] (print surface up) or [Face Down]
(print surface down) for paper orientation at output.
4. Press [OK].

Function defaults

Set the defaults for available settings such as copying
and sending. Setting the frequently-used values as
defaults makes subsequent jobs easier.
Original orientation
Set the original orientation defaults.
1. Press [Next] of Function Defaults and then
[Change] of Original Orientation.
2. Press [Top Edge Top] or [Top Edge Left].
3. Press [OK].
Continuous scan
Set the continuous scan defaults.
1. Press [Next] of Function Defaults and then
[Change] of Continuous Scan.
2. Press [Off] or [On].
3. Press [OK].
Original image
Set the default original document type.
1. Press [Next] of Function Defaults and then
[Change] of Original Image.
2. Select [Text+Photo], [Text] or [Photo].
3. Press [OK].
Resolution
Select the default scanning resolution.
1. Press [Next] of Function Defaults and then
[Change] of Scan Resolution.
2. Select the default resolution.
600 x 600 dpi/400 x 400 dpi Ultra Fine/300 x 300
dpi/200 x 400 dpi Super Fine/200 x 200 dpi Fine/
200 x 100 dpi Normal.
3. Press [OK].
Color selection
Select the default scanning color setting.
1. Press [Next] of Function Defaults and then
[Change] of Color Selection.
2. Select the default color setting.
Full color/Grayscale/Monochrome
3. Press [OK].
File format
Select the default file type to send the scanned originals.
1. Press [Next] of Function Defaults and then
[Change] of File Format.
2. Select the default file format.
TIFF/PDF/JPEG/High Comp. PDF*
*Only when the optional PDF upgrade kit is
installed.
3. Press [OK].
File separation
Select the default file separation setting.
1. Press [Next] of Function Defaults and then
[Change] of File Separation.
2. Press [Off] or [Each Page].
3. Press [OK].
2GN/2GP/2GR-7
1-3-93