Precautions On Adjusting - Sony DCR-PC101E Service Manual

DCR-PC101/PC101E
3-1-2.

Precautions on Adjusting

1) This set is adjusted in two modes, VTR mode and CAMERA
mode.
To activate the VTR mode, set the POWER switch to the
"VIDEO" position, or select the "Forced VTR Power ON
Mode" with the adjusting remote commander. (Note 1)
To activate the CAMERA mode, set the POWER switch to the
"CAMERA" position, or select the "Forced CAMERA Power
ON Mode" with the adjusting remote commander. (Note 2)
After the adjustment finished, be sure to cancel the "Forced
VTR Power ON Mode" or "Forced CAMERA Power ON
Mode". (Note 4)
2) To remove the cabinet (R), disconnect the following connec-
tor:
VC-284 board, CN1003 (88P, 0.4mm)
The DC IN terminal is attached to the BJ-003 board on the
cabinet (R). Accordingly, the BJ-003 board must be connected
to the VC-284 board. To remove the BJ-003 board from the
cabinet (R), disconnect the following connectors. (The LCD
block and the battery terminals need not be connected. In op-
erating the VTR, use the adjusting remote commander.)
1. BJ-003 board, CN006 (6P, 0.5mm)
2. BJ-003 board, CN007 (20P, 0.8mm)
3. BJ-003 board, CN001 (3P, 1.5mm)
Connect the BJ-003 board and the VC-284 board with the fol-
lowing connector:
VC-284 board, CN1003 (88P, 0.4mm)
3) The lens block need not be connected. If removing it, discon-
nect the following connector:
VC-284 board, CN1010 (88P, 0.4mm)
4) If the VC-284 board, CN1010 is disconnected (the lens block
is removed), the lithium 3V battery is removed accordingly,
and the data including date, time, and user set menus are erased.
After the adjustment finished, re-set these data. However, the
diagnostic data and history data (drum run time, user's first
power ON date, last dew occurring date) are not erased even if
the lithium 3V battery is removed. (For the diagnostic data
and history data, see "5-4. Service Mode".)
5) In the "Forced VTR Power ON Mode", the VTR can be oper-
ated even if the operation switch block (PS-2850) is removed.
To remove this block, disconnect the following connector:
ME-020 board, CN402 (10P, 0.5mm)
Note 1: Setting the "Forced VTR Power ON" mode (VTR mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 02, and press
the PAUSE button of the adjustment remote com-
mander.
The above procedure will enable the VTR power to
be turned on with the power switch (PS-2850 block)
removed.
After completing adjustments, be sure to exit the
"Forced VTR Power ON mode".
Note 2: Setting the "Forced Camera Power ON" mode (Camera
mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press
the PAUSE button of the adjustment remote com-
mander.
The above procedure will enable the camera power
to be turned on with the power switch (PS-2850
block) removed.
After completing adjustments, be sure to exit the
"Forced Camera Power ON mode".
Note 3: Setting the "Forced Memory Power ON" mode (Memory
mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 05, and press
the PAUSE button of the adjustment remote com-
mander.
The above procedure will enable the memory power
to be turned on with the power switch (PS-2850
block) removed.
After completing adjustments, be sure to exit the
"Forced Memory Power ON mode".
Note 4: Exiting the "Forced Power ON" mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press
the PAUSE button of the adjustment remote com-
mander.
3) Select page: 0, address: 01, and set data: 00.
5-44