Related Manuals for Interlogix TVE-400
Summary of Contents for Interlogix TVE-400
- Page 1 TVE-400/800-1600 H.264 IP Video Encoder User Manual P/N 1072585C-EN • REV 1.0 • ISS 16OCT12...
- Page 2 Copyright © 2012 UTC Fire & Security Americas Corporation, Inc. Interlogix is part of UTC Climate Controls & Security, a unit of United Technologies Corporation. All rights reserved. Trademarks and The Interlogix name and logo are trademarks of United patents Technologies.
-
Page 3: Table Of Contents
Scheduling record settings 32 Managing user accounts 35 Playback 38 Encoder management 40 Searching system logs 40 Restoring default settings 40 Viewing device information 41 Restarting the device 41 Importing/exporting parameters 41 Upgrading the system 42 TVE-400/800-1600 H.264 IP Video Encoder User Manual... -
Page 4: Specifications
Specifications 43 TVE-400/800-1600 H.264 IP Video Encoder User Manual... -
Page 5: Introduction
Bi-directional audio • Local PTZ control via RS-485/422 port and burnt-in multiple PTZ protocols • 4 alarm in/1 alarm out • Support ONVIF, PSIA and CGI communication • Discoverable via the TruVision Discovery Tool TVE-400/800-1600 H.264 IP Video Encoder User Manual... -
Page 6: Product Description
Connect a 12 V power supply via a PSU. RS-485 Connect a PTZ camera or dome camera to the RS-485 serial port. Alarm Out Connect up to one alarm relay outputs. Alarm In Connect up to four alarm relay inputs. TVE-400/800-1600 H.264 IP Video Encoder User Manual... -
Page 7: Connections
14N34 IN(n) ALM(+) optocoupler Relay input V-output ALM(-) Alarm input connections for normal alarm: JQC-3FG 24 V relay Alarm ALM(+) IN(n) V-output ALM(-) Relay input TVE-400/800-1600 H.264 IP Video Encoder User Manual... - Page 8 The TVE encoder supports the open/close relay input as the alarm output mode. The alarm input can be selected to NO or NC. Different alarm output connection methods are applied to the AC or DC load. See Figure 3. TVE-400/800-1600 H.264 IP Video Encoder User Manual...
-
Page 9: Network Settings
5. The program requires a utility called WinPcap to be installed on the computer. If it is already installed, go to step 6. If the program is not installed, the WinPcap window appears. Follow the on- screen instructions. TVE-400/800-1600 H.264 IP Video Encoder User Manual... - Page 10 The list of TruVision devices located on your network appears. Note: The TruVision Device Finder can only detect devices that are on the same LAN. The tool cannot detect devices placed on a VLAN. TVE-400/800-1600 H.264 IP Video Encoder User Manual...
- Page 11 6. Repeat this process for each device that needs to be modified. When all changes to all discovered devices is complete, press Exit to close the tool. Note: You must reboot to activate the new IP address or subnet mask. TVE-400/800-1600 H.264 IP Video Encoder User Manual...
-
Page 12: Using A Web Browser
The main page of the encoder appears. 3. If you need to install the TruVision Device Finder, click the center of the screen to start downloading it. The tool can be found on the CD shipped with the product. TVE-400/800-1600 H.264 IP Video Encoder User Manual... -
Page 13: Menu Tree
Menu tree Figure 5: Encoder menu tree TVE-400/800-1600 H.264 IP Video Encoder User Manual... -
Page 14: Live View
Define how you want video to be displayed in the viewer; single screen, 2X2, 3X3 or 4X4 (2X2 shown above). When in multiview mode, double-click on a video tile to get full-screen mode. Double-click again to return to multiview mode. TVE-400/800-1600 H.264 IP Video Encoder User Manual... -
Page 15: Capturing A Snapshot
The image is saved as a JPEG file on the computer. Note: Configure where the snapshots are saved on your computer in the Configuration > Local Configuration page. PTZ control You can control PTZ cameras from the encoder in live view mode. TVE-400/800-1600 H.264 IP Video Encoder User Manual... - Page 16 1. In live view mode, select a preset from the preset list. 2. Use the directional, zoom, focus and iris buttons to position the camera in the desired preset location. 3. Click to save the position. TVE-400/800-1600 H.264 IP Video Encoder User Manual...
-
Page 17: Video Image Settings
2. Move the slider to adjust the brightness, contrast, saturation and hue. Note: The range of adjustment is 0 to 100. The default setting is 60. Click Default to restore the default settings. TVE-400/800-1600 H.264 IP Video Encoder User Manual... -
Page 18: Configuration
Save video file to: Set the saving path for the manually recorded video files. Save live pictures to: Set the saving path for the manually captured pictures in live view mode. Save playback picture to: Set the saving path for the captured pictures in playback mode. TVE-400/800-1600 H.264 IP Video Encoder User Manual... -
Page 19: Time Settings
National Time Center (IP Address: 210.72.145.44) or europe.ntp.pool.org. If the encoder is set up in a more customized network, NTP software can be used to establish a NTP server used for time synchronization. TVE-400/800-1600 H.264 IP Video Encoder User Manual... -
Page 20: Network Set Up
Before configuring this function, you must first install the SNMP software. To configure basic settings: 1. Click the Device Configuration > Network Settings > Basic Settings. The Basic Settings window appears. TVE-400/800-1600 H.264 IP Video Encoder User Manual... - Page 21 Enter the alternate domain name server to use with the encoder. 3. Click Save to save the settings. To configure PPPoE settings: 1. Click the Device Configuration > Network Settings > PPPoE Settings. The PPPoE Settings window appears. 2. Check Enable PPPoE. TVE-400/800-1600 H.264 IP Video Encoder User Manual...
- Page 22 Attached image Check the box if you want to send email with attached alarm JPEG images. Sender name Enter the name of the sender of the e-mail. Sender’s address Enter the sender’s e-mail address. TVE-400/800-1600 H.264 IP Video Encoder User Manual...
- Page 23 The capacity, free space, status, type and property of the added network disk are displayed. If the status of the network disk is Uninitialized, select the disk and click Init start initializing it. When the initialization is complete, the disk status becomes Normal. TVE-400/800-1600 H.264 IP Video Encoder User Manual...
- Page 24 5. Select the security level: “no auth, no priv”, “auth, no priv” or “auth, priv”. 6. When the security level is set to “auth, priv”, configure the Authentication Algorithm and Privacy Algorithm parameters. TVE-400/800-1600 H.264 IP Video Encoder User Manual...
-
Page 25: Camera Set Up
6. Select how you want the camera information displayed. Select one of the options from the drop-down list. Default is non- transparent/non-flashing. • Transparent & flashing • Transparent & not flashing • Non-transparent & flashing • Non-transparent & non-flashing TVE-400/800-1600 H.264 IP Video Encoder User Manual... -
Page 26: Video Streaming Set Up
You can adjust the video recording parameters to obtain the image quality and file size best suited to your needs. To configure video settings: 1. Click Device Configuration > Camera Settings > Video Settings. Video Setting window appears. TVE-400/800-1600 H.264 IP Video Encoder User Manual... -
Page 27: Motion Detection
Motion detection The encoder can be set up to trigger an alarm if it detects motion and to record it. You can then search these recorded motion activities for specific incidents. TVE-400/800-1600 H.264 IP Video Encoder User Manual... - Page 28 Drag the Sensitivity scroll bar to the desired sensitivity level. The highest value is on the right of the bar. Click Save to save the settings. 5. Select the recording schedules for motion detection. Click the Arming schedule tab. Click Edit. TVE-400/800-1600 H.264 IP Video Encoder User Manual...
- Page 29 You can schedule up to eight time periods in a day. Default is 24 hours. Click OK. Note: Time periods defined cannot overlap. 6. Select the response method to motion detection. Click the Linking Method tab. TVE-400/800-1600 H.264 IP Video Encoder User Manual...
- Page 30 Select a time out option: 5, 10, and 30 seconds, 1, 2, 5, and 10 minutes, and Manual clear. If “Manual clear” is selected, the alarm output will stop only when the alarm input stops. TVE-400/800-1600 H.264 IP Video Encoder User Manual...
-
Page 31: Alarm Input Settings
Trigger an audible beep when an alarm is detected Notify surveillance center: Send a notification or alarm signal to remote alarm host when an event occurs. The alarm host refers to the computer installed with remote client software TVE-400/800-1600 H.264 IP Video Encoder User Manual... -
Page 32: Video Loss
You can set up your encoder to detect video loss and trigger a system notification. To configure video loss detection: 1. Click Device Configuration > Camera Settings > Video Loss. The Video Loss window appears. TVE-400/800-1600 H.264 IP Video Encoder User Manual... -
Page 33: Tamper-Proof Alarm
Note: It is strongly recommended not to configure for video tampering when using PTZ dome cameras. To configure tamper-proof detection: 1. Click Device Configuration > Camera Settings > Tamper-Proof. Tamper-Proof Settings window appears. TVE-400/800-1600 H.264 IP Video Encoder User Manual... -
Page 34: System Notification
Abnormal record: No space on the HDD to save recorded files. • Abnormal video signal: Poor video quality. To set up system notifications: 1. Click Device Configuration > Notification. The Notification window appears. TVE-400/800-1600 H.264 IP Video Encoder User Manual... -
Page 35: Privacy Masking
To configure a privacy mask: 1. Click Device Configuration > Camera Settings > Privacy Mask. Privacy Mask window appears. 2. Select camera for which to set up privacy masking. 3. Check the Enable Privacy Mask box. TVE-400/800-1600 H.264 IP Video Encoder User Manual... -
Page 36: Rs-485 Settings
Description of the record schedule window Defining a recording schedule lets you specify when the encoder records video and under what circumstances. Each camera can be configured to have its own recording schedule. TVE-400/800-1600 H.264 IP Video Encoder User Manual... - Page 37 4. Timeline (TL). There is a 24-hour time line for each day. Each square in the timeline represents an hour in the 24-hour period. Up to eight recording periods can be scheduled during the 24-hour period. TVE-400/800-1600 H.264 IP Video Encoder User Manual...
- Page 38 Note: To configure different schedules for other days, click the tab for the desired day and set the schedule. 8. Click to save the settings. Return to the Record Schedule window. 9. Schedule pre and post recording times. Click Advanced and select the desired times. TVE-400/800-1600 H.264 IP Video Encoder User Manual...
-
Page 39: Managing User Accounts
By default the encoder comes with three user accounts: an Administrator account, an Operator account and a Guest account. These accounts provide multiple levels of access and functionality. See Table 2 on page 36 for a description of the different user accounts. TVE-400/800-1600 H.264 IP Video Encoder User Manual... - Page 40 Note: Only a system administrator can create a user. You can add up to 31 new users. 2. Click Add. The Modify User window appears. 3. Enter the user name and password. Both the user name and password can have up to 16 alphanumeric characters. TVE-400/800-1600 H.264 IP Video Encoder User Manual...
- Page 41 1. Click Configuration > Device Configuration > User Management. User Information window appears. 2. Click Delete. 3. Click OK in the pop-up window to confirm deletion. The user is immediately deleted. 4. Click OK. TVE-400/800-1600 H.264 IP Video Encoder User Manual...
-
Page 42: Playback
Drag the bar to an exact spot where you want playback to start. Playback control toolbar Play back recording. Stop playback. Decrease playback speed: Options available are: single frame, 1/8 speed, ¼ speed, ½ speed, normal, X2 speed, X4 speed, X8 speed, maximum speed. TVE-400/800-1600 H.264 IP Video Encoder User Manual... - Page 43 5. To select an exact time to start playback, drag the time bar to where you want playback to start . You can also enter the exact time into the time selection box and click TVE-400/800-1600 H.264 IP Video Encoder User Manual...
-
Page 44: Encoder Management
Restore: All parameters except those for IP address, subnet mask, gateway, and server port are restored to factory default settings. Default: All parameters are restored to factory default settings. 3. Click to confirm you want to restore default settings. TVE-400/800-1600 H.264 IP Video Encoder User Manual... -
Page 45: Viewing Device Information
The configuration files of the device can be exported to a local back-up device. The configuration files of one device can be imported to multiple device devices if they are to be configured with the same parameters. TVE-400/800-1600 H.264 IP Video Encoder User Manual... -
Page 46: Upgrading The System
To upgrade the encoder: 1. Click Configuration > Maintenance. The Maintenance window appears. 2. Under “Remote Upgrade”, click Browse to locate the upgrade file from a local back-up device. Click Upgrade to start importing. TVE-400/800-1600 H.264 IP Video Encoder User Manual... - Page 47 PAL / NTSC adaptive Audio compression G.711 1-ch, RCA connector (2 Vp-p, 1 kΩ) Audio input 1-ch, RCA (2.0 Vp-p, 1 kΩ) Bi-directional audio input (Using AUDIO IN) 1-ch, RCA connector (Linear, 1 kΩ) Audio output TVE-400/800-1600 H.264 IP Video Encoder User Manual...
- Page 48 CIF@ 6 fps or QCIF@25 fps (P) / 30 fps (N) Video bit rate 32 kbps to 2048 kbps, or user-defined (Max. 3072 kbps) Stream type Video/ Video & Audio Audio bit rate 64 kbps Dual stream Support TVE-400/800-1600 H.264 IP Video Encoder User Manual...
- Page 49 Operating temperature -10 to +55 C° (14 to 131 °F) Operating humidity 10 to 90% Dimensions 315 × 45 × 201 mm (12.4 × 1.77 × 7.91 in.) Weight 1.6 kg (3.53 lb) TVE-400/800-1600 H.264 IP Video Encoder User Manual...
- Page 50 TVE-400/800-1600 H.264 IP Video Encoder User Manual...