Panasonic KX-FLM652CX Service Manual page 66

KX-FLM652CX
6.2.3. SERVICE FUNCTION TABLE
Code
501 Pause time set
502 Flash time
503 Dial speed select
507 Transmit speed select
508 Receive speed select
514 Bell signal detect time
520 CED frequency select
521 International mode select
522 Auto standby select
523 Receive equalizer select
524 Transmission equalizer select
527 V.8 function select
529 Memory clear for Call Service
550 Memory clear
551 ROM check
552 DTMF single tone test
553 Monitor on FAX communication
select
554 Modem test
555 Scan check
556 Motor test
557 LED test
558 LCD test
561 KEY test
570 BREAK % select
571 ITS auto redial time set
572 ITS auto redial line disconnection
time set
573 Remote turn-on ring number set
574 DIAL TONE detection ON/OFF
selection
590 FAX auto redial time set
591 FAX auto redial time disconnection
time set
592 CNG transmit select
Function Set Value
X 100 msec
X 10 ms
1:10 pps
2:20 pps
0: Disable
1: 33.6
2: 31.2
3: 28.8
4: 26.4
5: 24.0
6: 21.6
7: 19.2
8: 16.8
0: Disable
1: 33.6
2: 31.2
3: 28.8
4: 26.4
5: 24.0
6: 21.6
7: 19.2
8: 16.8
X 100msec
1:2100 Hz
2:1100 Hz
1:ON 2:OFF
1:ON 2:OFF
1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
1:OFF 2:ON
1:ON 2:OFF
1:OFF
2:PHASE B
3:ALL
1:61% 2:67%
X number of
times
X second
X number of
rings
1:ON / 2:OFF
X number of
times
X second
1:OFF
2:ALL
3:AUTO
Effective Default
Range
001~600 030
01~99 70
1, 2 1
0~8 1
0~8 1
1~99 6
1, 2 1 See Symptom/Countermeasure Table for long
distance and international calls in (P.126).
1, 2 1 See Symptom/Countermeasure Table for long
distance and international calls in (P.126).
1, 2 1 The resolution reverts to the default when
transmission is complete.
1~4 1 Set RX equalizer to automatic mode.
1~4 1 Set TX equalizer to automatic mode.
1, 2 2 Sets whether to select V.8 function or not.
Refer to Memory Clear Specification (P.68).
See (P.69).
1, 2 2 See (P.69).
1~3 1 Sets whether to monitor the line signal with the
unit´s speaker during FAX communication or not.
See (P.69).
See (P.69).
0 See (P.69).
See (P.69).
See (P.69).
See (P.69).
1, 2 1 Sets the % break of pulse dialing according PBX.
00~99 00 Selects the number of times that ITS is redialed
(not including the first dial).
001~999 065 Sets the interval of ITS redialing.
01~99 10 Sets the number of rings before the unit starts to
operate TAM in the TEL mode.
1, 2 2 Sets whether to dial the Automatic dial number
before detecting dial tone or after detecting
dialtone.
00~99 05 Selects the number of redial times during FAX
communication (not including the first dial).
001~999 065 Sets the FAX redial interval during FAX
communication.
1~3 2 Lets you select the CNG output during FAX
transmission. ALL: CNG is output at phase A.
AUTO: CNG is output only when automatic dialing
is performed. OFF: CNG is not output at phase A.
Refer to (P.119).
66
Remarks
----------
----------
----------
----------
----------
----------