External Hard Disk Drives - JVC VR-716E Instructions Manual

Useful Features (continued)

External Hard Disk Drives

VR-716 allows connection of up to 4 external hard disk drives in addition to the 2 built-in hard disks. Follow the procedure below to
alter the connection setup of the hard disk. There are 3 ways of altering connection setup, namely "NEW", "CHANGE" and "DIS-
CONNECT".
<Rear Panel of VR-716>
AUDIO IN
1 2 3 4 5 6 7
VIDEO IN
THRU OUT
SCSI
AUDIO OUT VIDEO OUT
LAN
1 2 1
RS-232C UPS
When connecting to 4 external
hard disk drives (connection up
to 4 hard disk drives is possible)
When connecting to multiple hard disk drives
• Set a separate SCSI ID No. for each hard disk and ensure that there
are no duplicate values.
• Connect the last hard disk drive in the series to the terminator.
(Refer to the instruction manual of the hard disk drive to be connected
for procedure on setting the SCSI ID No. as well as termination.)
<Alteration of Connection Setup>
• "NEW" : Connect to a new hard disk
drive.
• "CHANGE" : Replace the hard disk drive
currently connected with
another hard disk.
• "DISCONNECT" : Disconnect the hard disk
drive currently connected.
Once a hard disk drive is
disconnected, images re-
corded on the hard disk
cannot be viewed even
when it is reconnected.
Notes
• For the external hard disk and cable that
can be connected, consult your nearest JVC
dealer.
• The external hard disk drive will not func-
tion properly if its power is turned on after
turning on VR-716.
• Turn off the power of VR-716 before turn-
ing off the power of external hard disk.
• When turning off the power of the external
hard disk in the OPERATE OFF status of
this unit, disconnect this unit from the wall
outlet together.
Caution
• Recording will not be performed properly
and this unit will restart automatically if the
power supply of external hard disk is turned
off during recording.
Do not turn off the power supply of external
hard disk during operation.
62
8 9 10 11 12 13 14 15
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
2
AVIS:RISQUE DE CHOC
ELECTRIQ
1 4/ 16 5 8
1 3 5 7 9 11 13 15 RST COM IN IN EXT REC
CLK SER
2 4 6 8 10 12 14 16 9 12 13 16
OUT WAR RST REC
COM
ALARM OUT OUT
OUT EE OUT
Terminator
<SCSI Standards on Expansion >
16
AC IN
(220V–240V )
SIGNAL GND
1.
Turn OFF the power
• Turn off the power by following the procedure on 'Turning OFF the Power'
in 'Turning ON/OFF the Power' on page 15.
• External hard disk drive cannot be detected even if it is connected with
the power turned off. Connect only after unplugging the power cord.
2.
Connect the external hard disk drive and turn ON
the power
• Turn on the power of the external disk drive before doing so for
VR-716.
3.
Turn ON the power of VR-716
• Turn on the power by following the
procedure on 'Turning ON the Power' in
'Turning ON/OFF the Power' on page
15.
• The "HDD RECONFIGURING" screen
will be displayed.
Interface
Connector
Maximum Transfer Rate
SCSI ID
Notes
• Maximum transfer rate is not guaranteed.
• Consult the outlet from which this equipment
is purchased on the types of HDD and cable
that can be connected.
HDD RECONFIGURING
EXTERNAL HDD 4: 115GB NEW
HDD CONFIGURATION CHANGED
PUSH [EXEC] FOR ABOVE HDD APPLY
(ALL RECONFIGURING DATA IS DELETED!)
Ultra Wide SCSI
Half Pitch D-sub
68 Pin
20 MB/s
Use values between
0 ~ 3 (4 and above
cannot be used)
PUSH [CANCEL] TO QUIT