JVC VR-716E Instructions Manual page 28

Menus (continued)
"ALARM/SENSOR MODE" Menu (continued)
[ ● ] are factory settings. (Setting is disabled when in the Recording mode.)
Item
● "OFF"
"EXT INPUT OPERAT-
ING MODE"
● "OFF"
"MOTION DETECT"
"MOTION DETECT
SETTING"
● "STANDARD"
"SCENE"
"AREA SETTING"
28
Settings
For setting alarm or sensor recording actions for the signal input/output terminal
[ALARM IN] of VR-716.
"ON"
"NORMAL" "OFF"
"ON"
"TIMER"
"NORMAL"
"TIMER"
☞ Page 66 'Activation of Recording Via External Alarm/Sensor Signals'
For setting alarm or sensor recording using Motion Detect.
"OFF"
"ON"
"ON"
"NORMAL"
"NORMAL"
"TIMER"
"TIMER"
☞ Page 68 'Using the Motion Detect Feature'
For setting the sensitivity of the Motion Detect feature.
"MANUAL" Sensitivity is set upon selecting an item in "SCENE".
"DOORWAY"
"DOORWAY H"
"DOORWAY L"
"PASSAGE"
"PASSAGE H"
"PASSAGE L"
"REGISTER H" "REGISTER"
"REGISTER L"
"ATM H"
"ATM L" "ATM"
"LOBBY H"
"LOBBY"
"LOBBY L"
"GATE"
"GATE H"
"GATE L"
"PARKING LOT H"
"PARKING LOT"
"PARKING LOT L"
"LOW LUX H"
"LOW LUX L" "LOW LUX"
"ELEVATOR"
"ELEVATOR"
"COUNTER"
"COUNTER"
The following details can be specified when "MANUAL" is selected:
"DETAIL SETTING" for each camera
"DETECTING SENSITIVITY" ..................... 1 ~ 15 (Factory setting: 7)
"TERMINATION SENSITIVITY" ................. + 0 ~ 14 (Factory setting: + 3)
"OBJECT SIZE LEVEL" .............................
"DETECTING SENSITIVITY" : Level for detection. The higher the value, the higher the sen-
"TERMINATION SENSITIVITY" : An offset level for detection sensitivity. The higher the value,
"OBJECT SIZE LEVEL" : Level for the size of the object to be detected. The higher
☞ Page 68 'Using the Motion Detect Feature'
For setting the area from which motion is to be detected using the Motion Detect
feature.
☞ Page 68 'Using the Motion Detect Feature'
: Alarm/sensor recording not activated.
: Alarm/sensor recording activated.
: Alarm/sensor recording activated except when in the Timer
Recording or Timer Standby mode.
: Alarm/sensor recording activated when in the Timer Re-
cording or Timer Standby mode.
: Motion Detect not activated.
: Motion Detect activated.
: Motion Detect activated except when the Program Timer is
in the Standby mode.
: Motion Detect activated when the Program Timer is in the
Standby mode.
: To detect the opening and closing of the door of building
and shop, or people going in and out.
: To detect the movement of people on the passageway in
the school, corporation or shop.
: To detect the movement of people operating the cash reg-
ister in the shop/change machine in amusement center, or
the change in the waiting queue.
: To detect the change in users at the entrance of ATM termi-
nals of bank or post office.
: To detect the movement of people in the wide lobby.
: To detect the opening and closing of the door at a dim en-
trance or employee use entrance, or people going in and
out.
: To detect the cars going in and out of the entrance of car
parks outside a house.
: To detect the movement of people outside a dark house.
: To detect the opening and closing of an elevator door, or
people going in and out.
: To detect the visitors going in and out at the reception of
hotel, corporation or shop.
"SCENE" setting is a reference. Please try other settings if the sensitivity does
not suit your requirement.
sitivity.
the lesser the interruption to the alarm detection.
Valid when the sum of "DETECTING SENSITIVITY" and "TERMINATION SEN-
SITIVITY" is 15 or less. If the value is set to more than 15, it will be automatically
adjusted to the maximum value when exiting setting.
the value the lower the sensitivity to detect the motion of
small objects.
Description
1 ~ 10 (Factory setting: 2)