Table of Contents
Advertisement
Ku-Band Satellite Transceiver
Terminal Mode Commands
Program
Command
Preset
Response
Configuration
Status
Response
Clear Program
Command
Preset
Response
Configuration
Status
Response
Select Receive
Command
Band
Response
Status
Response
B.3.2
System Configuration Commands
Lock Mode
Command
Response
Status
Response
Address
Command
Select
Response
Status
Response
Baud Rate
Command
Select
Response
Status
Response
Parity
Command
Select
Response
Status
Response
Reference
Command
Frequency
Response
Adjust
Status
Response
LNA or LNB
Command
Calibration
Response
LNA or LNB
Command
Fault Enable
Response
Status
Response
<add/PGM_n'cr'
>add/PGM_n'cr''lf']
<add/PGM_'cr'
>add/PGM_n'cr'
1 – xxxxxxxxxx'cr'
2 – xxxxxxxxxx'cr'
3 – xxxxxxxxxx'cr'lf']
<add/CPGM_n'cr'
>add/CPGM_n'cr''lf']
<add/CPGM_'cr'
>add/CPGM_'cr'
1 – xxxxxxxxxx'cr'
2 – xxxxxxxxxx'cr'
3 – xxxxxxxxxx'cr'lf']
<add/SRB_n'cr'
>add/SRB_n'cr''lf']
<add/SRB_'cr'
>add/SRB_n'cr''lf']
<add/LM_xx'cr'
Where:
>add/LM_xx'cr''lf']
<add/LM_'cr'
>add/LM_xx'cr''lf']
<add/AS_xxx'cr'
Where:
>add/AS_xxx'cr''lf']
<add/AS_'cr'
>add/AS_xxx'cr''lf']
<add/BR_xxxxx'cr'
Where:
>add/BR_xxxxx'cr''lf']
<add/BR_'cr'
>add/BR_xxxxx'cr''lf']
<add/PS_xx'cr'
Where:
>add/PS_xx'cr''lf']
EV (Even)
Note: Selecting ODD or EVEN parity programs the KST-2000A
<add/PS_'cr'
to respond to 7,O,2 or 7,E,2 data formats.
>add/PS_xx'cr''lf']
Selecting parity = NONE will set the KST-2000A to 8,N,1.
<add/RFJ_nnn'cr'
Where:
>add/RFJ_nnn'cr''lf']
Fine tunes the internal 10MHz high stability reference oscillator.
<add/RFJ_'cr'
>add/RFJ_nnn'cr''lf']
<add/CLNAB_'cr'
Note: This only needs to be done once during the initial
>add/CLNAB_'cr''lf']
installation. It calibrates the unit to determine the normal LNA or
LNB power consumption.
<add/LFE_xxx'cr'
Where:
>add/LFE_xxx'cr''lf']
<add/LFE_'cr'
>add/LFE_xxx'cr''lf']
Note: States whether or not the system should take action upon
any, or report any, LNA or LNB fault notifications.
B–6
Where:
n = 1, 2, or 3
xxxxxxxxxx = "Programmed" or "None"
Allows the user to store (program) the current Up Converter and
Down Converter frequency and attenuator settings as one of the
three "PreSet" selections.
Ref: SEL_ command for additional information.
Where:
n = 1, 2 or 3
xxxxxxxxx = "Programmed" or "None"
Allows the user to clear (unprogram) the frequency and
attenuator setting for one of the three "PreSet" selections.
Where:
n = (A) for selecting frequency band 10950.0
to 11700.0 MHz inclusive.
(B) for selecting frequency band 11700.0
to 12200.0 MHz inclusive.
(C) for selecting frequency band 12250.0
to 12750.0 MHz inclusive.
Note: This command will not be recognized for the
KST-2000A. It will only be recognized for the KST-2000B.
LM = LK (Lock) or DS (Disable),
Default = DS
add = Present Address
xxx = New Address
Default: Address = 1
xxxxx = 300, 600, 1200, 2400, 4800, 9600, or 19200
Default = 9600
xx = OD (Odd), EV (Even) or NO (None)
nnn = Current DAC setting from 0 to 255
xxx= ON/OFF,
Default is ON
Revision 9
MN/KST2000AB.IOM
Default =
Advertisement
Table of Contents
