Daily Maintenance; Weekly Maintenance; Monthly Maintenance - Star Trac S-UBx Owner's Manual

2. Install the Rear Foot
Lift up the rear of the bike frame and place the rear foot assembly
in position under the frame, aligning the holes in the foot with the
holes in the frame.
Using four M10 X 30 button head screws, secure the rear foot
assembly to the frame. Tighten all four screws securely.
3. Install the Display Console
NOTE: It is necessary to have one person support and position the
display console while a second person makes the cable connections.
Carefully pull the cable bundle out of the lower neck on the bike
frame. Use a pair of wire cutters or other suitable tool to cut and
remove the tie wrap from the cable bundle.
Hold the display console neck approximately one inch from the
neck brackets of the bike frame. Plug the display console power,
main I/O and Coax cable into their mating connectors in the
display console neck.
NOTE: The power connector is a "loose" fit. A strip of electrical tape
for securing the power connector is provided inside the lower neck
on the bike frame.
While holding the power cable connectors together, make a small
"bundle" of the cable, and wrap with electrical tape to prevent the
connectors from separating.
12
Step 2
Step 3a
Step 3b
Step 3c
STAR TRAC S SERIES BIKES O ' M
WNER S ANUAL
A P P
UTO ILOT ROGRAM
The Auto Pilot program allows the user to positively increase the level of resistance by increasing pedaling speed (rpm's). No keys
to press with this one!
To operate the Auto Pilot program:
1. Mount the bike (please refer to "Seat Adjustments" section) and begin pedaling.
If necessary, enter the Lockout ID to enable the bike for operation (see "Lockout ID Processing" for details).
n
2. Press the key.
3. You are prompted to select the desired A
DVANCED
A P program.
UTO ILOT
4. If desired, you can use the personal fan during your workout (see "Using the Personal Fan" for details).
5. You can increase the resistance L during the program by increasing your pedaling speed. Decreasing your pedaling
EVEL
speed will lower the resistance L .
EVEL
6. If you wish to pause the program, stop pedaling. The bike enters pause mode and a "P" flashes in the TIME Window.
Resume pedaling within 25 seconds to continue your workout.
7. When you have reached your workout goal, the bike enters the Cooldown cycle (see "Cooldown Cycle" for details). If you
wish to exit the program before you have reached your workout goal, stop pedaling and allow the Pause timer to expire.
P M
REVENTATIVE AINTENANCE
With durable, high performance components, STAR TRAC S SERIES BIKES are designed for heavy usage with minimal
maintenance required. To keep your bike in top condition, Star Trac strongly recommends performing the regular daily, weekly
and monthly preventive maintenance routines outlined below. Any unusual symptoms, such as a loud continuous noise during
operation, should be reported to STAR TRAC PRODUCT SUPPORT DEPARTMENT at (800) 503-1221, or USA 1-714-669-
1660.

DAILY MAINTENANCE

Remove excessive accumulations of dust, dirt, and other substances by using a clean, soft cloth and a non-abrasive liquid
n
cleaner, such as Formula 409TM or FANTASTIK™. Wipe down the exterior of the display panel, handlebars, seat, pedals,
shrouds and heart rate grips.
NOTE: DO NOT spray the cleaner directly onto the display panel or heart rate grips.

WEEKLY MAINTENANCE

Perform the following services each week:
Vacuum the floor under and around the bike. Move the bike to another spot, if necessary, to vacuum thoroughly.
n
Inspect the display panel mounting screws for security, and retighten if necessary.
n
Inspect the display panel keypads for wear.
n

MONTHLY MAINTENANCE

Perform the following services each month, or as needed:
Check that the seat, pedals and shrouds are secure.
n
Tighten the pedals onto their respective pedal cranks using a 5/8-inch open end wrench.
n
STAR TRAC S SERIES BIKES O ' M
WNER S ANUAL
W program. Press the key when prompted to select the
ORKOUTS
29