Epson EPL-N2700 Service Manual page 44

EPSON EPL-N2700 / N2750
Table 1-24. EPL-2750 SelecType Option
MENU Button
ITEM Button
*46
LC2 Counter Clear
*46
LC3 Counter Clear
MP Counter Clear
TR Counter Clear
Error Log Clear
NOTES:
1. Indicated only when Network I/F=On.
2. Indicated and can be selected only when Level 3 network I/F card is installed and
Network I/F=On.
3. Indicated and can be selected only when optional PostScript 3 DIMM is installed.
4. This item is not indited on the panel.
5. Indicated only when optional PostScript 3 DIMM is installed.
6. Indicated only when optional TypeB interface is installed.
7. Indicated and can be selected only when an optional lower cassette unit is installed.
8. When A4 controller is selected, the default of the paper setting jumper becomes A4;
When Letter controller is selected, the default of the paper setting jumper becomes
LT.
9. Indicated and can be selected only when optional 5 bin or 10 bin multi bin unit is
installed and the Stacker mode is selected.
10.Indicated and can be selected only when optional 5 bin or 10 bin multi bin unit is
installed and the Mailbox mode is selected. 5 bin multi bin corresponds from Mailbox
1 to 5, and 10 bin multi bin corresponds from Mailbox 1 to 10.
11.Indicated and can be selected only when optional 5 bin or 10 bin multi bin unit is
installed and the Sorter mode or MultiShort mode is selected.
12.Not indicated on the panel; Not printed on the status sheet. Can be set by EJL or
PJL.
13.This item is valid against PCL5e, ESC/Page, ESC/P2, FX, 1239X mode.
14.Indicated and can be selected only when optional Duplex unit is installed.
15.Indicated and can be selected only when optional 5 bin multi bin unit is installed.
16.When AUTO is selected, the following paper size will be automatically detected
according to the controller market destination.
For A4 controller: A3, A4, A5, IB5, LTR, LGL, F4.
For Letter controller: LT, HLT, LGL, EXE, GLG, GLT, B
17.This item is only for indication and can not be changed.
Product Description
VALUE Button
Panel Operation
18.Indicated only when optional lower cassette is installed.
19.Indicated and can be changed only when optional lower cassette is installed.
20.Indicated only when an optional Duplex Unit is installed.
21.STANDBY command of the EJL is also supported. The default is 60 minutes. (Not
intended for users.)
22.Does not appear on the panel nor status sheet. Only set in EJL.
23.Indicated but not to be selected.
24.Indicated and selected only when optional 5 bin or 10 bin mail bin unit is installed.
When you change the settings and close the panel setting mode, the printer warm-
boots.
25.When you changed this item, it will be immediately reflected to the Status Sheet EJL
read back. However, the settings will become valid only when warm-booting or
turning on the printer again.
26.When you changed this item by panel or by EJL, it will not become valid until warm-
boot or turning on the printer again. If you indicate this setting on the panel or read
out from EJL, it will be immediately reflected to the status sheet printing. The setting
is not reflected on outbin setting range, language and network operation until warm-
boot or turning on the printer again. If you change the setting by panel or by EJL, be
sure to warm-boot or turn on the printer again. If you want to change some settings,
change all settings you want and then warm-boot or turn on the printer only once at
last.
27.After shifting to "Ready", it automatically returns to "Network Config = No".
28.Indicated and selected only when "Network Config = Yes". Always printed on Status
Sheet.
29.Indicated and can be changed only when an optional Type B interface is installed.
30.Indicated and can be changed only when Level 3 interface card is installed. When
the printer is ready to print, it automatically returns to "AUX Config =No".
31.Indicated and can be selected and executed only when "AUX Congif=Yes" is
selected. The setting value shifts to the printing ready situation and will become valid
when the network card is re-booted. Due to this, when you changed the setting, if
"AUX Status Sheet" of the test print menu is executed before panel setting mode is
closed, the setting value before changed will be printed.
If you want to set or execute menu items other than described here, be sure to do so
after the printer becomes ready to print.
32.When you changed the items on the panel or by EJL, the value will not become valid
until warm-boot or turning on the printer. It will be immediately reflected on panel
indication, reading out by EJL, printing on status sheet. he setting is not reflected on
outbin setting range, language and network operation until warm-boot or turning on
the printer again. If you change the setting by panel or by EJL, be sure to warm-boot
or turn on the printer again. If you want to change some settings, change all settings
you want and then warm-boot or turn on the printer only once at last.
Revision B
44