Sony DSR-DR1000 Operating Instructions Manual page 73

VIDEO CONTROL [Video]: Settings related to video control Description of settings
SRCH CONTROL [>Srch ctrl]: Select the frame display style
during high-speed searching.
AUDIO CONTROL [Audio]: Settings related to audio
control
REC MODE [> REC mode]: Select the audio recording mode. *2 CHANNEL (48kHz) [>> 2 ch]: 2-channel, 48-kHz mode
INPUT ARRANGE [> Input arng]: Make settings for input
audio mixing.
Note
When, in 4-channel mode, analog audio is selected for all four
channels (channels 1/2 and 3/4), the same analog audio
signals are recorded on channels 1 and 3 and on channels 2
and 4, respectively. That is, the analog signal recorded on
channel 1 is also recorded on channel 3 and the analog signal
recorded on channel 2 is also recorded on channel 4.
You can adjust the audio level on each of the four channels
separately using the REC/PB LEVEL control knobs with the
VARIABLE switch set to REC.
LEVEL SELECT [> Level Sel] REF LEVEL [>> REF
Level]:
Select the audio
reference level
(headroom) for
recording.
CH1 IN LEVEL [>> CH1
input]:
Select the audio level
setting according to the
audio level of the signal
input to the AUDIO IN
1/3 connector.
CH2 IN LEVEL [>> CH2
input]:
Select the audio level
setting according to the
audio level of the signal
input to the AUDIO IN
2/4 connector.
OUTPUT LEVEL [>> Out
Level]:
Select the analog
audio output reference
level.
* BLEND [>>blend]: Display frames blended with each other.
CLEAR [>>clear]: Display frames independently with no
noise.
Description of settings
4 CHANNEL (32kHz) [>> 4 ch]: 4-channel, 32-kHz mode
Set the channels on which to record the input audio signals as
follows.
(1) Use the cursor/clip operation buttons to move the cursor
and the SET button to toggle the setting on and off.
(2) To save the settings, press the MENU button to return to
the previous screen, then press the SET button.
Example settings:
AUDIO INPUT SOURCE
ARRANGE
in1 in2 in3 in4
ch1:*on
ch2: on
ch3:
ch4
ON/OFF :
TO MENU :
1 Input audio channel 1 ("in1") is recorded on audio channel 1
("ch1") on tape.
2 Input audio channels 2 and 4 ("in2" and "in4") are recorded
mixed on audio channel 2 ("ch2") on tape.
3 Input audio channel 4 ("in4") is recorded on audio channel 3
("ch3") on tape.
4 Input audio channel 3 ("in3") is recorded on audio channel 4
("ch4") on tape.
*–20 dB [>>> –20dB] (factory default setting for DSR-
DR1000)
*–18 dB [>>> –18dB] (factory default setting for DSR-
DR1000P)
–16 dB [>>> –16dB]
–12 dB [>>>–12dB]
*+4 dBm [>>> +4dBm]
0 dBm [>>> 0dBm]
–3 dBm [>>> –3dBm] (for DSR-DR1000P only)
–6 dBm [>>> –6dBm]
*+4 dBm [>>> +4dBm]
0 dBm [>>> 0dBm]
–3 dBm [>>> –3dBm] (for DSR-DR1000P only)
–6 dBm [>>> –6dBm]
*+4 dB [>>> +4dB]
0 dB [>>> 0dB]
–3 dB [>>> –3dB] (for DSR-DR1000P only)
–6 dB [>>> –6dB]
1
2
on
on
on
3
SET KEY
MENU KEY
4
Menu Contents
73