Page 1
NOTE: Please read all instructions carefully before using this product MARCY DIAMOND ELITE Table of Contents Safety Notice SMITH MACHINE Hardware Identifier MD-4100 Assembly Instruction Parts List Warranty Ordering Parts Model MD-4100 Retain This Manual for Reference 09-25-07 OWNER'S MANUAL ®...
EXPLODED DIAGRAM…………………………………………………………….. PARTS LIST………..……………………………………………………………….. WARRANTY....................… ORDERING PARTS..................BEFORE YOU BEGIN Thank you for selecting the MARCY DIAMOND ELITE MD-4100 Smith Machine ® by IMPEX INC. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction.
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1.
WARNING LABEL PLACEMENT The warning labels shown here have been placed on the Cross Brace and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown.
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten all nuts and bolts until instructed to do so. B.) Attach one Base Frame (#1) to the Left Rear Vertical Frame (#5).
Page 9
STEP 2 (See Diagram 2) A.) Insert one Guide Rod (#24) into the hole on the Left Base Frame (#1). Secure the bottom with one M10 x 1” Allen Bolt (#59). B.) Slide the Left Lower Safety Stop Frame (#20) onto the Guide Rod from the top. Slide the Safety Stop Frame (#19) onto the Guide Rod from the top.
Page 10
STEP 3 (See Diagram 3) A.) Attach the Rear Vertical Frame Base (#9) to the Cross Brace (#8). Attach the Rear Vertical Frame (#10) to the Cross Brace. Align the holes and secure them together with two M10 x 2 3/8” Carriage Bolts (#67), Ø ¾” Washers (#73), and M10 Aircraft Nuts (#75). B.) Slide the Sliding Pulley Bracket (#14) onto the Rear Vertical Frame.
Page 11
STEP 4 (See Diagram 4) A.) Attach the Upper Frame (#11) to the top of the Rear Vertical Frame (#10). Attach two Cover Brackets (#12) to the Upper Frame and the Rear Vertical Frame. Secure them together with four M10 x 2 3/8” Carriage Bolts (#67), Ø ¾” Washers (#73), and M10 Aircraft Nuts (#75). B.) Attach the two Cover Brackets to the Weight Glide Post (#13).
Page 13
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach the 135” Upper Cable (#54) to the front opening on the Upper Frame (#11). Attach a Pulley (#42) to the opening. Secure it with one M10 x 2 1/8” Allen Bolt (#60), two Ø 1 1/8” x 3/8” Pulley Bushings (#58), and one M10 Aircraft Nut (#75).
Page 15
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach the “Ball” on the 245” High-Low Cable (#55) in between two Small Pulleys (#43). Attach the two Small Pulleys to the Sliding Pulley Bracket (#14). Secure each Small Pulley to the Bracket with one M10 x 1 ¾” Allen Bolt (#62), two Ø ¾” Washers (#73), and one M10 Aircraft Nut (#75).
Page 17
STEP 7 (See Diagram 7) A.) NOTE: Help of another person is strongly recommended for this step. Place the Lifting Sleeve (#22) in between the two Safety Stop Frames (#19). Align the holes and insert the Weight Bar (#27) all the way through. Center the bar and secure it with two M8 x 3/8” Allen Bolts (#71) on each side.
PARTS LIST KEY NO. DESCRIPTION Q’ty Base Frame 1 ½” End Cap Left Front Vertical Frame Lock Knob Right Front Vertical Frame 3” x 2 ½” Sleeve Panel 135” Upper Cable Left Rear Vertical Frame 245” High-Low Cable Right Rear Vertical Frame Ø...
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser.