NOTE: Please read all instructions carefully before using this product MARCY DIAMOND ELITE Table of Contents OLYMPIC BENCH Safety Notice Hardware Pack MD-867 Assembly Instruction Parts List Warranty Ordering Parts Model MD-867 Retain This Manual for Reference 100708 OWNER'S ®...
PARTS LIST………….…………...............………. 12 WARRANTY....................…………. 13 ORDERING PARTS..................………… 13 BEFORE YOU BEGIN Thank you for selecting the Marcy Diamond Elite MD-867 BENCH by ® IMPEX INC. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction.
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1.
WARNING LABEL PLACEMENT The Warning Label shown here has been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown...
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten all nuts and bolts until instructed to do so. B.) Attach the Left Diagonal Support (#8) to the Left Upright Beam (#1) from rear.
Page 8
STEP 2 (See Diagram 2) A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Attach the Main Seat Support (#4) to the Cross Brace (#5). Secure it with four M10 x 2 3/8” Carriage Bolts (#49), one 5 ½” x 3” Bracket (#21), four Ø ¾” Washers (#55), and four M10 Aircraft Nuts (#58).
Page 9
A.) Attach the Seat Incline Support (#18) to the opening on Seat Bracket (#17). Secure it with one M10 x 5” Allen Bolt (#51), two Ø ¾” Washers (#55), and one M10 Aircraft Nut (#58). Do not tighten the Nut and Bolt yet. B.) Attach the Seat Bracket to the pivot on the Sliding Block (#14).
Page 10
A.) Attach the Leg Developer (#11) to the Front Post (#3). Secure it with an Axle (#43), two M10 x 3/4” Allen Bolts (#52) and two ¾” Washers (#55). B.) Insert two Foam Tubes (#20) halfway through the holes on the Leg Developer. Push four Foam Rolls (#27) onto the Tubes from both ends.
Page 11
A.) Attach the Arm Curl Pad (#24) to the Arm Curl Stand (#10). Secure it with two M8 x 5/8” Allen Bolts (#53) and two Ø 5/8” Washers (#56). B.) Insert the Arm Curl Stand into the top opening on the Front Post (#3). Use a M18 Lock Knob (#39) to secure the Arm Curl Stand in position.
PARTS LIST KEY NO. DESCRIPTION Q’ty Left Upright Beam M10 x 5” Allen Bolt Right Upright Beam M10 x ¾” Allen Bolt Front Post M8 x 5/8” Allen Bolt Main Seat Support M8 x 1 5/8” Allen Bolt Cross Brace Ø...
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option.