Summary of Contents for Impex MARCY DIAMOND MD-844
Page 1
Safety Notice MD-844 Hardware Pack Assembly Instruction Exploded Diagram Parts List Warranty Ordering Parts Model MD-844 Retain This Manual for Reference 05/08/09 ® IMPEX INC. 2801 S. Towne, Pomona, CA 91766 OWNER'S Tel: (800) 999-8899 Fax (626) 961-9966 www.impex-fitness.com MANUAL info@impex-fitness.com...
ORDERING PARTS..................BEFORE YOU BEGIN Thank you for selecting the MARCY DIAMOND WEIGHT BENCH MD-844 by ® IMPEX INC. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction.
OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. SAVE THESE INSTRUCTIONS.
Page 4
WARNING LABEL REPLACEMENT The Warning Labels shown here have been placed on the Base Frame. If the label i missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown...
ASSEMBLY INSTRUCTION Tools Required For Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended for two or more people to assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach one Rear Base Frame (#3) to the Base Frame (#2). Attach an Upright Beam (#1) onto the Base Frame and Rear Base Frame.
Page 9
STEP 2 (See Diagram 2) A.) Attach the Main Seat Support (#6) to the Base Frame (#2). Secure it with two M10 x 3 ½” Carriage Bolts (#43), one 4 ¾” x 2” Bracket (#15), two Ø ¾” Washers (#53), and two M10 Aircraft Nuts (#57).
Page 10
STEP 3 (See Diagram 3) A.) Attach the holes on the end of the two Backrest Supports (#8) to the pivot on the Main Seat Support (#6). Secure the two Backrest Supports to the pivot with one M12 x 6 1/8” Hex Bolt (#42), two Ø...
Page 11
STEP 4 (See Diagram 4) A.) Attach two Ø ¾” Leg Developer Bushings (#27) to the Leg Developer (#11). Attach the Leg Developer to the Front Post (#10). Secure it with one M10 x 3 1/8” Allen Bolt (#46), two Ø ¾” Washers (#53), and one M10 Aircraft Nut (#57). Do not over tighten the Nut and Bolt.
Page 12
STEP 5 (SEE DIAGRAM 5) A.) Attach the Arm Curl Pad (#23) to the Arm Curl Bracket (#19). Secure it with two M8 x 5/8” Allen Bolts (#50) and two Ø 5/8” Washers (#54). B.) Attach the Arm Curl Bracket to the bracket on the Arm Curl Stand (#9). Insert the M10 x 3 1’2” Allen Bolt (#45) through the open track on the Arm Curl Stand and the holes on the Arm Curl Bracket then secure the Bolt with two Ø...
PARTS LIST KEY NO. DESCRIPTION QUANTITY Upright Beam Base Frame Rear Base Frame Left Crutch Right Crutch Main Seat Support Backrest Adjustment Bar Backrest Support Arm Curl Stand Front Post Leg Developer Arm Curl Handle Foam Tube 5 ½” x 2” Bracket 4 ¾”...
IMPEX. IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential damages or whatsoever natures.