Parts List Warranty Ordering Parts Model MD-805 Retain This Manual for Reference 06-24-08 OWNER'S MANUAL MARCY WEIGHT BENCH MD-805 IMPEX 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.com ® DIAMOND ® INC.
To avoid unnecessary delays, please call our TOLL-FREE customer service number. Agents will provide immediate assistance to you. Toll-Free Customer Service Number Mon. - Fri. 9 a.m. - 5 p.m. PST www.impex-fitness.com info@impex-fitness.com ® MD-805 Weight Bench by IMPEX 1-800-999-8899 Our Customer Service ®...
OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. SAVE THESE INSTRUCTIONS.
Page 4
WARNING LABEL REPLACEMENT The Warning Label shown here has been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown.
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the Left and Right Upright Beams (#45 & #1) by a Cross Brace (#2) in the Mid- span.
Page 7
STEP 2 (See Diagram 2) A.) Attach the Front Post (#5) to the Main Seat Support (#4). Secure it with five M10 x ¾” Allen Bolts (#44) and Ø ¾” Washers (#41). DO NOT tighten the Bolts yet. B.) Attach the Main Seat Support to the Cross Brace (#2). Secure it with two M10 x 3 1/8” Carriage Bolts (#34), one 4 ¾”...
Page 8
STEP 3 (See Diagram 3) A.) Attach the Leg Developer (#7) to the open bracket on the Front Post (#5). Secure it with one M8 x 3 3/8” Allen Bolt (#37), two Ø 5/8” Washers (#42), and one M8 Aircraft Nut (#40).
Page 9
STEP 4 (See Diagram 4) A.) Attach the side holes on the two Backrest Supports (#12) to the pivot on the Main Seat Support (#4). Place the other end rest against the Backrest Adjustment Bar (#9). B.) Attach the Backrest Board (#15) onto the Backrest Supports. Secure it with four M6 x 1 ½” Hex Bolts (#38) and Ø...
Page 10
STEP 5 (See Diagram 5) A.) Insert two Foam Tubes (#11) halfway through the holes on the Leg Developer (#7). Push four Foam Rolls (#13) onto the Tubes from both ends. Plug four Foam Roll End Caps (#25) into the ends. B.) Attach the Olympic Sleeve (#20) onto the weight post on the Leg Developer.
PARTS LIST KEY NO. DESCRIPTION Right Upright Beam Cross Brace Crutch Main Seat Support Front Post Arm Curl Stand Leg Developer Arm Curl Handle Backrest Adjustment Bar 4 ¾” x 2” Bracket Foam Tube Backrest Support Foam Roll Seat Pad Backrest Board Arm Curl Pad Crutch Sleeve...
IMPEX. IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential damages or whatsoever natures.