1. Manuals
  2. Brands
  3. Impex Manuals
  4. Home Gym
  5. MARCY DIAMOND ELITE MD-3401
  6. Owner's manual

Impex MARCY DIAMOND ELITE MD-3401 Owner's Manual

Marcy diamond elite home gym
Hide thumbs Also See for MARCY DIAMOND ELITE MD-3401:
Table of Contents

Advertisement

Quick Links

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MD-3401
Retain This
Manual for
Reference
120609
OWNER'S
MANUAL
MARCY DIAMOND ELITE
MD-3401 HOME GYM
IMPEX
2801 S. Towne Ave, Pomona CA 91766
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
®
INC.

Advertisement

Table of Contents
loading

Related Manuals for Impex MARCY DIAMOND ELITE MD-3401

Summary of Contents for Impex MARCY DIAMOND ELITE MD-3401

  • Page 1 NOTE: Please read all instructions carefully before using this product MARCY DIAMOND ELITE Table of Contents MD-3401 HOME GYM Safety Notice Hardware Identifier Assembly Instruction Parts List Warranty Ordering Parts Model MD-3401 Retain This Manual for Reference 120609 OWNER'S ®...

  • Page 2: Table Of Contents

    BEFORE YOU BEGIN ® by IMPEX Thank you for selecting the MARCY DIAMOND Home Gym MD-3401 For your safety and benefit, read this manual carefully before using the machine. As a manufacturer , we are committed to provide you complete customer satisfaction. If...

  • Page 3: Important Safety Notices

    IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1.

  • Page 4: Warning Label Placement

    WARNING LABEL PLACEMENT The warning labels shown here have been placed on the Rear Stabilizer and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown.

  • Page 5: Hardware Pack

    HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
  • Page 6 HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
  • Page 7 HARDWARE PACK...

  • Page 8: Assembly Instructions

    ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended that this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Insert two Guide Rods (#16) into the holes on the Rear Stabilizer (#15). Secure each Guide Rod with one M10 x ¾”...
  • Page 9 DIAGRAM 1...
  • Page 10 STEP 2 (See Diagram 2) A.) Attach the Upper Frame (#1) onto the two Guide Rods (#16). Secure it with two M10 x ¾” Allen Bolts (#78) and  ¾” Washers (#92). DO NOT tighten the Bolts yet. B.) Place the Upper Frame (#1) onto the Vertical Frame (#4). Secure it with two M10 x 2 ¾”...
  • Page 11 STEP 3 (See Diagram 3) A.) Attach the Front Press Base (#2) to the Upper Frame (#1). Secure it with one 6 ¾” Front Press Base Axle (#29), two Ø 1 ¼” Washers (#59), and two M10 Aircraft Nuts (#91). B.) Attach the Front Press (#3) to the Front Press Base (#2).
  • Page 12 DIAGRAM 3...
  • Page 13 STEP 4 (See Diagram 4) A.) Attach the Seat (#32) to the Seat Post (#6). Secure it with two M8 x 1 5/8” Allen Bolts (#86) and Ø 5/8” Washers (#88). B.) Insert the Seat Post into the opening on the Seat Support Frame (#7). Thread the Lock Knob (#40) into the hole on the Seat Support Frame to lock the Seat at selected height.
  • Page 14 STEP 5 (See Diagram 5) A.) Slide the Right Butterfly (#10) onto the right axle on the Butterfly Base (#13). B.) Insert the Butterfly Handle (#9) into the pivot on the Right Butterfly. Secure it with one M10 x ¾” Allen Bolt (#78) and  1 ¼” Washer (#59) from the bottom. C.) Repeat Procedures A and B above to install the other side.

  • Page 15: Cable Loop Diagram

    CABLE LOOP DIAGRAM STEP 6 (See Diagram 6 & Upper Cable Loop Diagram)
  • Page 16 A.) Attach the 165” Upper Cable (#33) to the opening on the front of Upper Frame (#1). Make sure the ball stopper is underneath the Frame. Attach a Pulley (#47) to the Cable. B.) Secure the Pulley to the opening with one M10 x 3 ½” Allen Bolt (#77), two Pulley Bushings (#49), and one M10 Aircraft Nut (#91).
  • Page 17 DIAGRAM 6...
  • Page 18 Upper Cable Loop Diagram...
  • Page 19 STEP 7 (See Diagram 7 & Lower Cable Loop Diagram) A.) Attach the 164” Lower Cable (#35) to the opening on the Leg Developer (#8). Attach a Pulley (#47) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#84), two  7/8”...
  • Page 20 Lower Cable Loop Diagram...
  • Page 21 STEP 8 (See Diagram 8 & Butterfly Cable Loop Diagram)
  • Page 22 A.) Clip one end of the 98” Butterfly Cable (#34) to the open slot on the Right Butterfly (#10). B.) Draw the Cable to the open bracket on the right side of the Vertical Frame (#4). Attach a Small Pulley (#73) to the bracket C.) Secure it with one M10 x 1 ¾”...
  • Page 24 Butterfly Cable Loop Diagram...
  • Page 25 STEP 9 (See Diagram 9) A.) Connect the Lat Bar (#24) to the Upper Cable (#33) with two Hooks (#37) and one Chain (#36). B.) Connect the Abdominal Strap (#70) to the Lower Cable (#35) with a Hook. C.) Connect the Shiver Bar (#19) to the Lower Cable with two Hooks and a Chain. Replace Shiver Bar with Single Handle (#68) or Ankle Strap (#69) for various exercises.
  • Page 26 Step 10 (See Diagram 10) A.) Attach the two Weight Stack Covers (#74) with four 3” Sleeve (#94) to the Upper Frame (#1) and Rear Stabilizer (#15). B.) Secure them with four M10 x 3¾” Allen Bolts (#82) and four Ø ¾” Washers (#92). DIAGRAM 10...

  • Page 27: Weight Resistance Chart

    WEIGHT RESISTANCE CHART WEIGHT PLATE Station Low Pulley Lat Pull Butterfly Front Press AB Crunch Leg Developer WEIGHT PLATE Station Low Pulley Lat Pull Butterfly Front Press AB Crunch Leg Developer *Numbers are approximate. Actual weight may vary. *Value for butterfly is for each arm.

  • Page 28: Parts List

    PARTS LIST KEY NO. DESCRIPTION Q’ty Upper Frame Ø 1 ¼” Front Press Bushing Front Press Base Ø 7/8” Leg Developer Bushing  1” Bushing Front Press Vertical Frame Ø 1” Spacer Backrest Support Frame Rubber Bumper Seat Post Ø 1 ½” Spacer Seat Support Frame Ø...

  • Page 29: Warranty

    ® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser.

Table of Contents