Page 1
NOTE: Please read all instructions carefully before using this product MARCY DIAMOND ELITE Table of Contents OLYMPIC BENCH Safety Notice Hardware Pack MD-867W Assembly Instruction Parts List Warranty Ordering Parts Model MD-867W Retain This Manual for Reference 130522 OWNER'S ®...
PARTS LIST………….…………...............………. 12 WARRANTY....................…………. 13 ORDERING PARTS..................………… 13 BEFORE YOU BEGIN Thank you for selecting the Marcy Diamond Elite MD-867W BENCH by ® IMPEX INC. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction.
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1.
WARNING LABEL PLACEMENT The Warning Label shown here has been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown...
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten all nuts and bolts until instructed to do so. B.) Attach the Left Diagonal Support (#8) to the Left Upright Beam (#1) from rear.
Page 8
STEP 2 (See Diagram 2) A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Attach the Main Seat Support (#4) to the Cross Brace (#5). Secure it with four M10 x 2 3/8” Carriage Bolts (#49), one 5 ½” x 3” Bracket (#21), four Ø ¾” Washers (#55), and four M10 Aircraft Nuts (#58).
Page 9
STEP 3 (See Diagram 3) A.) Attach the Seat Incline Support (#18) to the opening on Seat Bracket (#17). Secure it with one M10 x 5” Allen Bolt (#51), two Ø ¾” Washers (#55), and one M10 Aircraft Nut (#58). Do not tighten the Nut and Bolt yet.
Page 10
STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#11) to the Front Post (#3). Secure it with an Axle (#43), two M10 x 3/4” Allen Bolts (#52) and two ∅ ¾” Washers (#55). B.) Insert two Foam Tubes (#20) halfway through the holes on the Leg Developer. Push four Foam Rolls (#27) onto the Tubes from both ends.
Page 11
STEP 5 (See Diagram 5) A.) Attach the Arm Curl Pad (#24) to the Arm Curl Stand (#10). Secure it with two M8 x 5/8” Allen Bolts (#53) and two Ø 5/8” Washers (#56). B.) Insert the Arm Curl Stand into the top opening on the Front Post (#3). Use a M18 Lock Knob (#39) to secure the Arm Curl Stand in position.
PARTS LIST KEY NO. DESCRIPTION Q’ty M10 x 5” Allen Bolt Left Upright Beam M10 x ¾” Allen Bolt Right Upright Beam M8 x 5/8” Allen Bolt Front Post M8 x 1 5/8” Allen Bolt Main Seat Support Ø ¾” Washer Cross Brace Ø...
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser.