Panasonic WJ-FS616 Operating Instruction page 11

1. Alarm Indicator (ALARM)
This LED indicator (Red) lights up to indicate that
an alarm condition exists.
It goes off when the alarm is reset automatically.
To turn the indicator off, press the ALARM RESET
button.
2. Busy Indicator (BUSY)
This LED lights up to indicate that the system is
locked by PC command.
While this LED is lit, control from the video multi-
plexer and system controller is disabled.
3. Function Buttons (F1/F2/F3/F4)
These buttons are used to select functions dis-
played on the Liquid Crystal Display.
F1: Operates the multiscreen monitor.
F2: Operates the spot monitor.
F3: Activates the sequence mode.
In this mode, a series of camera pictures is
displayed in succession on the monitor
screen for the specified duration.
F4: Selects the camera picture or VTR play-
back picture to be displayed on the moni-
tor screen.
4. Liquid Crystal Display
This displays the function menu and function sta-
tus.
In this Instructions Manual, it is hereafter referred to
as the "LCD".
5. Arrow Buttons (A D B C)
These function as shown below.
Camera Set On Button (CAMERA SET ON A)
This button is used to display the camera setup
menu on the monitor screen.
Setup Button (SETUP D)
This button is used to display the Setup Menu of
the Video Multiplexer.
Camera Set Off Button (CAMERA SET OFF B)
This button is used to exit the camera setup menu
displayed on the monitor screen.
Time Lapse Mode Buttons (T / L MODE, D C)
These buttons, used in combination with the
Alternate button, select the time lapse mode of the
Time Lapse VTR.
Press the (D) button to increase the recording
duration or the (C) button to decrease the record-
ing duration.
Reverse Play Button (REV A)
This button, used in combination with the Alternate
button, activates reverse playback on the Time
Lapse VTR.
Play Button (PLAY B)
This button, used in combination with the Alternate
button, activates playback on the Time Lapse VTR.
6. Joystick Controller
The joystick is used to operate the Pan/Tilt Head
manually, or to move the cursor to the desired posi-
tion on the setup menu of the Video Multiplexer.
7. Iris Control Buttons (IRIS, CLOSE / OPEN)
These buttons are used to close or open the lens
iris of the specified lens mounted on the camera.
When these buttons are pressed at the same time,
the lens iris is reset to the factory settings.
8. Focus Control Button (FOCUS, NEAR / FAR)
This button is used to adjust the lens focus of the
specified lens mounted on the camera.
9. Zoom Control Button (ZOOM, TELE / WIDE)
This button is used to adjust the lens zoom of the
specified lens mounted on the camera.
10. Auto Focus Button (AF)
This button is used to activate the auto focus func-
tion when the specified camera with auto focus fea-
ture is selected.
11. Camera Key (CAM)
Set Key (SET)
CAM: This key is used for camera selection. Press
the desired Numeric Keys, then press this key
to select the camera.
SET: This key is used to execute the currently high-
lighted setting on the setup menu of the Video
Multiplexer.
12. Numeric Keys (0-9)
These keys are used for numeric input into the sys-
tem, such as the number of a camera you want to
select.
13. Unit/Escape Key (UNIT / ESC)
This key is used to select the Video Multiplexer unit.
Press the desired Numeric Key, then press this key
to select a specific Video Multiplexer.
This key is also used to escape the currently high-
lighted setting in the setup menu of this appliance.
14. Still Button (STILL)
This button is used to still the picture displayed on
the monitor screen.
15. Preset Position Button (PRE-POSI)
This button is used to assign a preset position to
the specified camera.
-9-