Program Change - Roland JP-8080 Owner's Manual

Program Change

status 2nd byte
CnH ppH
pp=Program number : 00H - 7FH (prog.1 - prog.128)
* This is received when Tx/Rx ProgChg SW ([MIDI]) is PC or BANK SEL + PC.
* If this is received on the Perform Ctrl CH ([MIDI]), the performance will change. If this
is received on the Part MIDI CH ([PART]), the patch of that part will change. If the
Perform Ctrl CH and the Part MIDI CH are the same, only the performance will
change.
* In the case of a performance change, program numbers outside the range of 00H - 3FH
will be ignored.
* When this message is received, all voices will be turned off.
Channel Pressure
status 2nd byte
DnH vvH
* The Tx/Rx Setting ([MIDI]) will be valid when Tx/Rx Edit SW ([MIDI]) is ON and
Tx/Rx Edit Mode ([MIDI]) is set to MODE2. In this case, this message will change the
value of the parameter assigned to AFTERTOUCH in the part whose Part MIDI CH
([PART]) matches the MIDI channel of the channel pressure message which was
received.
* If Control Up/Control Down ([MIDI]) is set to AFTERTOUCH, this message will oper-
ate as controller up or down for the part whose Part MIDI CH ([PART]) matches the
MIDI channel on which the channel pressure message was received. With the factory
settings, Control Up is set to AFTERTOUCH.
Pitch Bend Change
status 2nd byte 3rd byte
EnH llH mmH
mm,ll=Pitch Bend value: 00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)
* This will modify the pitch of the notes of the part whose Part MIDI CH ([PART])
matches the MIDI channel on which the pitch bend change was received.
* The width of pitch change will be according to the patch parameter Bend Range Up
([PATCH]) and Bend Range Down ([PATCH]). A pitch bend value in the range of 00
00H - 3F 7FH will follow the Bend Range Down setting, and a value in the range of 40
01H - 7F 7FH will follow the Bend Range Up setting.
Channel Mode messages
All Sound Off (Controller number 120)
status 2nd byte 3rd byte
BnH 78H 00H
* When this message is received, all notes currently sounding on the corresponding
channel will be turned off.
Reset All Controllers (Controller number 121)
status 2nd byte 3rd byte
BnH 79H 00H
* When this message is received, the following controllers will be set to their reset val-
ues.
Controller Reset value
Pitch Bend Change 0 (center)
Modulation 0 (minimum)
Expression 127 (maximum)
Hold 1 0 (off)
RPN Unset. Previously set data will not change
(However, the Fine Tune of the Part is excepted.).
Control Up 0 (minimum) Default setting is Aftertouch.
Control Down 0 (minimum) Default setting is Breath.
All Note Off (Controller number 123)
status 2nd byte 3rd byte
BnH 7BH 00H
* When All Note Off is received, all currently sounding notes of the corresponding chan-
nel will be turned off. However if Hold 1 is on, the sound will be held until these are
turned off.
Omni Off (Controller number 124)
status 2nd byte 3rd byte
BnH 7CH 00H
* The same processing as when All Note Off is received will be done.
Omni On (Controller number 125)
status 2nd byte 3rd byte
BnH 7DH 00H
* The same processing as when All Note Off is received will be done.
Mono (Controller number 126)
status 2nd byte 3rd byte
BnH 7EH mmH
mm=Mono number: 00H - 10H (0 - 16)
* The same processing as when All Note Off is received will be done, and the MONO
Switch parameter will be set to ON.
Poly (Controller number 127)
status 2nd byte 3rd byte
BnH 7FH 00H
* The same processing as when All Note Off is received will be done, and the MONO
Switch parameter will be set to OFF.
System Realtime messages
Active Sensing
status
FEH
* When an Active Sensing message is received, the unit will begin monitoring the inter-
vals of all further messages. During monitoring, if more than 400 ms passes without a
message being received, the same processing will be done as when All Sound Off, All
Note Off, and Reset All Controllers messages are received. Then monitoring will be
halted.
Timing Clock
status
F8H
* This is received when MIDI Sync ([MIDI]) is set to MIDI IN.
Start
status
FAH
* This is received when MIDI Sync ([MIDI]) is set to MIDI IN.
Continue
status
FBH
* This is received when MIDI Sync ([MIDI]) is set to MIDI IN.
Stop
status
FCH
* This is received when MIDI Sync ([MIDI]) is set to MIDI IN.
193