Roland JP-8080 Owner's Manual page 198

3. MIDI messages transmitted from MIDI OUT
* When MIDI Thru is ON (ALL), messages received at MIDI IN will be re-transmitted
from MIDI OUT except for Active Sensing messages.
* When MIDI Thru is ON (w/o Sys.Ex), MIDI messages received at MIDI IN will be re-
transmitted from MIDI OUT except for Active Sensing and System Exclusive mes-
sages.
Channel voice messages
Note Off
status 2nd byte 3rd byte
8nH kkH vvH
9nH kkH 00H
Note On
status 2nd byte 3rd byte
9nH kkH vvH
Control Change
* When the Tx/Rx Edit SW ([MIDI]) is ON and Tx/Rx Edit Mode ([MIDI]) is set to
MODE2, the Tx/Rx Setting ([MIDI]) setting will be valid. In this case, operating the
sliders/knobs will cause the control change assigned to that parameter to be transmit-
ted on the Part MIDI CH ([PART]) of the part specified by PANEL SELECT.
* Tx/Rx settings ([MIDI]) can be made for controller numbers 1 to 31 and 33 to 95. Refer
to Transmit/Receive Setting List (p.188) for the default settings.
Bank Select
status 2nd byte 3rd byte
BnH 00H mmH
BnH 20H llH
mm,ll=Bank number: 00 00H - 7F 7FH (bank.1 - bank.16384)
* This is transmitted when Tx/Rx ProgChg SW ([MIDI]) is BANK SEL + PC.
* The Patches corresponding to each Bank Select are as follows.
-------------+--------------+--------------------------
Bank Select | Program No. |
MSB | LSB | |
------+------+--------------+--------------------------
50H | 00H | 00H - 3FH |
| 00H | 40H - 7FH |
------+------+--------------+--------------------------
51H | 00H | 00H - 3FH |
| 00H | 40H - 7FH |
| 01H | 00H - 3FH |
| 01H | 40H - 7FH |
| 02H | 00H - 3FH |
| 02H | 40H - 7FH |
------+------+--------------+--------------------------
52H | 00H | 00H - 3FH |
| 00H | 40H - 7FH |
| 01H | 00H - 3FH |
| 01H | 40H - 7FH |
| : | : |
| 1FH | 00H - 3FH |
| 1FH | 40H - 7FH |
+------+--------------+--------------------------
|*)20H | 00H - 3FH |
| 20H | 40H - 7FH |
| 21H | 00H - 3FH |
| 21H | 40H - 7FH |
| : | : |
| 3FH | 00H - 3FH |
| 3FH | 40H - 7FH |
------+------+--------------+--------------------------
*) Bank Select LSB 20H - 3FH is available only with the S4M-5.
* The Performances corresponding to each Bank Select are as follows.
-------------+--------------+--------------------------
Bank Select | Program No. |
MSB | LSB | |
------+------+--------------+--------------------------
50H | 00H | 00H - 3FH |
------+------+--------------+--------------------------
51H | 00H | 00H - 3FH |
| 01H | 00H - 3FH |
| 02H | 00H - 3FH |
------+------+--------------+--------------------------
52H | 00H | 00H - 3FH |
| 01H | 00H - 3FH |
| 02H | 00H - 3FH |
| : | : |
| 1FH | 00H - 3FH |
+------+--------------+--------------------------
|*)20H | 00H - 3FH |
| : | : |
| 3FH | 00H - 3FH |
------+------+--------------+--------------------------
*) Bank Select LSB 20H - 3FH is available only with the S4M-5.
198
(Controller number 0,32)
Group Patch No.
User A 11 - 88
User B 11 - 88
Preset 1 A 11 - 88
Preset 1 B 11 - 88
Preset 2 A 11 - 88
Preset 2 B 11 - 88
Preset 3 A 11 - 88
Preset 3 B 11 - 88
Card 01 A 11 - 88
Card 01 B 11 - 88
Card 02 A 11 - 88
Card 02 B 11 - 88
: :
Card 32 A 11 - 88
Card 32 B 11 - 88
Card 33 A 11 - 88
Card 33 B 11 - 88
Card 34 A 11 - 88
Card 34 B 11 - 88
: :
Card 64 A 11 - 88
Card 64 B 11 - 88
Group Perform No.
User 11 - 88
Preset 1 11 - 88
Preset 2 11 - 88
Preset 3 11 - 88
Card 01 11 - 88
Card 02 11 - 88
Card 03 11 - 88
: :
Card 32 11 - 88
Card 33 11 - 88
: :
Card 64 11 - 88
Modulation
status 2nd byte 3rd byte
BnH 01H vvH
Breath type
status 2nd byte 3rd byte
BnH 02H vvH
* When Control Up/Control Down ([MIDI]) is assigned to BREATH, settings of
VOICE MODULATOR [ON]
Vocal Morph Ctrl
Vocal Morph Sens
VocalMorph Thrsh
will mean that when audio is input to VOCAL/UPPER, breath type messages will be
transmitted on the Part MIDI CH of the part specified by PANEL SELECT (when KEY
MODE is SINGLE or SPLIT) or of both Upper and Lower parts regardless of PANEL
SELECT (when KEY MODE is DUAL). With the factory settings, BREATH is assigned
to Control Down.
Foot type
status 2nd byte 3rd byte
BnH 04H vvH
Portamento Time
status 2nd byte 3rd byte
BnH 05H vvH
Data Entry
status 2nd byte 3rd byte
BnH 06H mmH
BnH 26H llH
mm,ll= the value of the parameter specified by RPN/NRPN
mm=MSB, ll=LSB
Volume
status 2nd byte 3rd byte
BnH 07H vvH
Balance
status 2nd byte 3rd byte
BnH 08H vvH
Panpot
status 2nd byte 3rd byte
BnH 0AH vvH
Expression
status 2nd byte 3rd byte
BnH 0BH vvH
Effect Control1
status 2nd byte 3rd byte
BnH 0CH vvH
Effect Control2
status 2nd byte 3rd byte
BnH 0DH vvH
General Purpose Controller1–4
status 2nd byte 3rd byte
BnH 10-13H vvH
Hold1
status 2nd byte 3rd byte
BnH 40H xxH
Portamento
status 2nd byte 3rd byte
BnH 41H xxH
Sound Controller1–10
status 2nd byte 3rd byte
BnH 46-4FH vvH
(Controller number 1)
(Controller number 2)
ON
ON
-64 – -1
0 - 126
(Controller number 4)
(Controller number 5)
(Controller number 6, 38)
(Controller number 7)
(Controller number 8)
(Controller number 10)
(Controller number 11)
(Controller number 12)
(Controller number 3)
(Controller number 16–19)
(Controller number 64)
(Controller number 65)
(Controller number 70–79)