Roland JP-8080 Owner's Manual page 195

* When Tx/Rx Edit SW ([MIDI]) is ON and Tx/Rx Edit Mode ([MIDI]) is set to MODE2,
the Tx/Rx Setting ([MIDI]) will be valid. In this case, this message will change the
value of the parameter assigned to the received control change for the part specified by
PANEL SELECT. Also, a control change will be transmitted from MIDI OUT on the
Part MIDI CH ([PART]) of that part.
* Tx/Rx settings ([MIDI]) can be made for controller numbers 1 to 31 and 33 to 95. Refer
to Transmit/Receive Setting List (p.188) for the default settings.
Bank Select
status 2nd byte 3rd byte
BnH 00H mmH
BnH 20H llH
mm,ll=Bank number: 00 00H - 7F 7FH (bank.1 - bank.16384)
* Regardless of the Tx/Rx ProgChg SW ([MIDI]) setting, this is received when Remote
KBD CH ([MIDI]) is ALL or when the MIDI channel of the bank select message match-
es.
* If [PERFORM/PATCH SELECT] is off (PERFORM) when this message is received, the
performance bank will be specified. If [PERFORM/PATCH SELECT] is on (PATCH),
the bank of the patch for the part selected by PANEL SELECT will be specified.
* Bank Select processing will be suspended until a Program Change message is received.
* If an unavailable (nonexistent) Bank Select number is received it will be ignored, and
only the Program Change will be received.
* The Patches corresponding to each Bank Select are as follows.
-------------+--------------+--------------------------
Bank Select | Program No. |
MSB | LSB | |
------+------+--------------+--------------------------
50H | 00H | 00H - 3FH |
| 00H | 40H - 7FH |
------+------+--------------+--------------------------
51H | 00H | 00H - 3FH |
| 00H | 40H - 7FH |
| 01H | 00H - 3FH |
| 01H | 40H - 7FH |
| 02H | 00H - 3FH |
| 02H | 40H - 7FH |
------+------+--------------+--------------------------
52H | 00H | 00H - 3FH |
| 00H | 40H - 7FH |
| 01H | 00H - 3FH |
| 01H | 40H - 7FH |
| : | : |
| 1FH | 00H - 3FH |
| 1FH | 40H - 7FH |
+------+--------------+--------------------------
|*)20H | 00H - 3FH |
| 20H | 40H - 7FH |
| 21H | 00H - 3FH |
| 21H | 40H - 7FH |
| : | : |
| 3FH | 00H - 3FH |
| 3FH | 40H - 7FH |
------+------+--------------+--------------------------
*) Bank Select LSB 20H - 3FH can be used only with the S4M-5.
* The Performances corresponding to each Bank Select are as follows.
-------------+--------------+--------------------------
Bank Select | Program No. |
MSB | LSB | |
------+------+--------------+--------------------------
50H | 00H | 00H - 3FH |
------+------+--------------+--------------------------
51H | 00H | 00H - 3FH |
| 01H | 00H - 3FH |
| 02H | 00H - 3FH |
------+------+--------------+--------------------------
52H | 00H | 00H - 3FH |
| 01H | 00H - 3FH |
| 02H | 00H - 3FH |
| : | : |
| 1FH | 00H - 3FH |
+------+--------------+--------------------------
|*)20H | 00H - 3FH |
| : | : |
| 3FH | 00H - 3FH |
------+------+--------------+--------------------------
*) Bank Select LSB 20H - 3FH can be used only with the S4M-5.
Modulation (Controller number 1)
status 2nd byte 3rd byte
BnH 01H vvH
* This will control the pitch, cutoff, or amplitude modulation depth for the respective
PITCH/FILTER/AMP[DEPTH] parameter of MODULATION(LFO2).
* This is not reset to the default value when a patch program change is received.
* This will be reset to the default value when a performance program change is received.
(Controller number 0, 32)
Group Patch No.
User A 11 - 88
User B 11 - 88
Preset 1 A 11 - 88
Preset 1 B 11 - 88
Preset 2 A 11 - 88
Preset 2 B 11 - 88
Preset 3 A 11 - 88
Preset 3 B 11 - 88
Card 01 A 11 - 88
Card 01 B 11 - 88
Card 02 A 11 - 88
Card 02 B 11 - 88
: :
Card 32 A 11 - 88
Card 32 B 11 - 88
Card 33 A 11 - 88
Card 33 B 11 - 88
Card 34 A 11 - 88
Card 34 B 11 - 88
: :
Card 64 A 11 - 88
Card 64 B 11 - 88
Group Perform No.
User 11 - 88
Preset 1 11 - 88
Preset 2 11 - 88
Preset 3 11 - 88
Card 01 11 - 88
Card 02 11 - 88
Card 03 11 - 88
: :
Card 32 11 - 88
Card 33 11 - 88
: :
Card 64 11 - 88
Breath type
status 2nd byte 3rd byte
BnH 02H vvH
Foot type
status 2nd byte 3rd byte
BnH 04H vvH
Portamento Time
status 2nd byte 3rd byte
BnH 05H vvH
* This will modify the PORTAMENTO [TIME] value.
Data Entry
status 2nd byte 3rd byte
BnH 06H mmH
BnH 26H llH
Volume
status 2nd byte 3rd byte
BnH 07H vvH
Balance
status 2nd byte 3rd byte
BnH 08H vvH
Panpot
status 2nd byte 3rd byte
BnH 0AH vvH
Expression
status 2nd byte 3rd byte
BnH 0BH vvH
* This adjusts the volume of the part. Expression messages are used to create variation in
dynamics (expression pedal, crescendo, decrescendo etc.) while you play.
* This is not reset to the default value when a patch program change is received.
* This is reset to the default value when a performance program change is received.
Effect Control1
status 2nd byte 3rd byte
BnH 0CH vvH
Effect Control2
status 2nd byte 3rd byte
BnH 0DH vvH
General Purpose Controller1–4
status 2nd byte 3rd byte
BnH 10-13H vvH
Hold1
status 2nd byte 3rd byte
BnH 40H xxH
* This will hold notes which are currently in a note-on state.
Portamento
status 2nd byte 3rd byte
BnH 41H xxH
* This switches PORTAMENTO [ON] on/off.
Sound Controller1–10
status 2nd byte 3rd byte
BnH 46-4FH vvH
General Purpose Controllers 5–8
status 2nd byte 3rd byte
BnH 50-53H vvH
(Controller number 2)
(Controller number 4)
(Controller number 5)
(Controller number 6, 38)
(Controller number 7)
(Controller number 8)
(Controller number 10)
(Controller number 11)
(Controller number 12)
(Controller number 13)
(Controller number 16–19)
(Controller number 64)
(Controller number 65)
(Controller number 70–79)
(Controller number 80–83)
195