Table of Contents
Advertisement
PPP > Wakeup-On-Call Examples
Example 1 – Set Up the Ethernet Router to Activate on Incoming SMS Message
On the
1.
PPP > PPP Configuration
PPP General
●
Make sure that PPP is Disabled (the default).
●
Make sure Dial-on-Demand is Disabled (the default).
●
Set the Idle Time Out to the number of seconds you desire.
Authentication
●
Your wireless service provider may require you to have a separate PPP User name and Password. If so, enter
them here.
Note:
you when you activated your account.
Modem Configuration
●
Make sure your Dial Number is entered correctly: The Dial Number is *99***1#
●
Enter your APN. The APN is assigned by your wireless service provider.
Example: AT+CGDCONT=1,"IP","internet"
Submit
●
Click the Submit button to save the changes made on this screen.
On the
2.
PPP > Wakeup-on-Call
Wakeup-on-Call Configuration
●
Select Enable for Wakeup-on-Call.
●
Set the Time Delay. You can use the 10 second default.
●
Enter the Init Strings so that the integrated cellular modem receives SMS.
Enter Wakeup Init String 1 as at+cmgf=1
Enter Wakeup Init String 2 as at+csms=1
Enter Wakeup Init String 3 as at+cnmi=2,2,0,0,1
Enter Wakeup Init String 4 as at^scfg="URC/DstIfc",mdm
●
Click the Submit button to save these settings.
Caller ID Configuration
●
Enter an SMS that you want added to the Caller ID list.
Add the SMS message string into the Caller ID list. The SMS message string must not contain any spaces
Note:
between words. When the string configured matches the SMS message string, it will activate the Wakeup-on-
Call feature.
●
Add Button
Click the Add button to save each message as it is entered to the Caller ID list.
Caller Acknowledgement Configuration
●
Enter a configured string (0 to 40 characters) that will be sent to the integrated cellular modem upon receiving a
valid Caller ID from the WAN.
Set the Wakeup Acknowledgement string configuration with the command at+cnma
●
Click the Submit button to save the Acknowledgement Configuration.
You must click Save and Restart once you have completed and submitted all the screens on which you have made changes.
The device will save all the settings and reboot the PC.
Example 2 – Determine if the router Is Supporting Incoming Calls and Caller ID
On the PPP > PPP Configuration screen, make sure that PPP is Disabled.
1.
On the PPP > Wakeup-on-Call screen, make sure that Wakeup-on-Call is Disabled.
2.
Open a command prompt by clicking the Start button and selecting Run.
3.
Type CMD to open the command window. Click OK.
4.
When the command window opens, type Telnet 192.168.2.1 5000. This is the IP address of the router.
5.
5000 is the port number.
Note:
Enter your user name and password to login.
5.1.
Enter an AT command to make sure you receive a response; i.e., OK.
5.2.
Enter the Command AT+CNUM to determine the dial number of your router.
5.3.
From another phone, call your router using the number identified in Step 5.3. This will let you know if the RING
6.
message shows.
To enable Caller ID, enter the AT+CLIP=1 command on the command screen and make the call again to see if it
7.
shows Caller ID information.
Notes:
●
Step 5.3 must show the RING or CALLER ID information in order for the Wakeup-on-Call function to work.
●
Some wireless providers might not provide caller ID information if you have only a data plan.
Multi-Tech Systems, Inc. MultiModem rCell User Guide
screen, set up the following parameters:
If a user name and password are required, your wireless provider would have given them to
screen, set up the following parameters:
Chapter 3 – Using the Web Management Software
31
Advertisement
Table of Contents
