Loewe Xelos 32 LED Operating Instructions Manual page 25

Initial installation
Setting options for the satellite system
(max. 4 satellites on DiSEqC multiswitch):
Settings
INITIAL INSTALLATION (DVB-S)
DiSEqC
Repeat rate
multiswitch
Control voltage 13/18V
22kHz signal
Toneburst
Proceed
OK
Select and adapt settings for the DiSEqC multi-
switch.
Repeat rate The refresh rate determines how often a DiSEqC
command is output. A refresh is only necessary with
cascaded systems.
Control The control voltage controls the switching of the
voltage polarisation level (horizontal/vertical) in non-DiSEqC
capable components (e.g. control of single LNBs via
DiSEqC multiswitch).
22kHz signal The 22kHz signal controls the switching between high
and low band in the Band setting. The Position setting
controls the selection of the satellites in non-DiSEqC
capable components.
Toneburst The Toneburst controls the selection of the satellites in
non-DiSEqC but toneburst capable components with the
Position and Option settings.
OK Proceed
Satellite
INITIAL INSTALLATION (DVB-S)
selection
Satellite selection
Satellite 1
Satellite 2
Satellite 3
Satellite 4
Proceed
OK
Select Satellite 1 ... Satellite 4,
select satellites from list,
OK Proceed.
LNB
INITIAL INSTALLATION (DVB-S)
frequencies
LNB frequencies
ASTRA1 19,2°E Low band
ASTRA1 19,2°E High band
Hot Bird 13°E Low band
Hot Bird 13°E High band
Eutelsat W2 16°E Low band
Eutelsat W2 16°E High band
Proceed
OK
Set LNB frequencies.
You do not normally need to change the values.
OK Proceed.
(with Setting options for DVB-S reception (continued)
on page 26).
none 1 2
on
Band
off
Back
Astra1 19,2°E ...
Hot Bird 13°E
Eutelsat W2 16°E
none
Back
9750 MHz
10600 MHz
9750 MHz
10600 MHz
9750 MHz
10600 MHz
Back
Setting options for the satellite system
(DiSEqC one cable communal system):
DiSEqC one
INITIAL INSTALLATION (DVB-S)
cable
Select DiSEqC single cable communal installation
communal
DELTA SUM-514
DELTA SUM-516
system
DELTA SUM-518
DELTA SUM-918
DELTA SUM-928
KATHREIN EXR-551
KATHREIN EXR-552
KATHREIN EXR-501
Proceed
OK
Select DiSEqC single cable communal installation.
OK Proceed.
Satellite
INITIAL INSTALLATION (DVB-S)
selection
Satellite selection
Satellite 1
Proceed
OK
Select satellites from list,
OK Proceed.
LNB
INITIAL INSTALLATION (DVB-S)
frequencies
LNB frequencies
Low band
High band
Proceed
OK
Set LNB frequencies.
Normally, you do not need to change the values for
high and low band, unless the LNC (LNB) of your
satellite system uses a different oscillator frequency
(important for the frequency display).
OK Proceed.
Manual
INITIAL INSTALLATION (DVB-S)
registration
Manual registration (for socket ANT SAT)
Transmission channel
(for socket
Transmission frequency
ANT SAT) PIN protection
Define/change PIN
Proceed
OK
Select and adjust settings for the DiSEqC single
cable communal installation.
Transmission
Select the desired transmission channel and the corre-
channel /frequency
sponding transmission frequency.
PIN protection
If your system is designed for it, it is possible to protect
your used transmission data from use by other subscrib-
ers with a PIN.
OK Proceed.
(with Setting options for DVB-S reception (continued)
on page 26).
OK
Astra1 19,2°E ...
Back
9750 MHz
10600 MHz
Back
1 2 3
OK
1284
no
0000
4 5 6
25 -