Korg D1600mkII Owner's Manual page 162

68: MM14: Exciter – Limiter
[Excit2, Lmtr]
69: MM15: Exciter – Cho/Flng
[Excit2, ChFl1]
70: MM16: Exciter – Phaser
[Excit2, Phaser]
71: MM17: Exciter – Mt.Delay
[Excit2, Mt.Dly]
72: MM18: Limiter – P4EQ
[Lmtr, P4EQ]
73: MM19: Limiter – Cho/Flng
[Lmtr, ChFl2]
74: MM20: Limiter – Phaser
[Lmtr, Phaser]
75: MM21: Limiter – Mt.Delay
[Lmtr, Mt.Dly]
76: MM22: OD/HiG – Cho/Flng
[ODHiG, ChFl1]
77: MM23: OD/HiG – Phaser
[ODHiG, Phaser]
78: MM24: OD/HiG – Mt.Delay
[ODHiG, Mt.Dly]
79: MM25: OD/HiG – AmpSim
[ODHiG, AmpSim]
80: MM26: Wah – AmpSim
[Wah, AmpSim]
81: MM27: Decimator – AmpSim
[Decim, AmpSim]
82: MM28: Decimator – Comp
[Decim, Comp1]
83: MM29: Cho/Flng – Mt.Delay
[ChFl2, Mt.Dly]
84: MM30: Phaser – Cho/Flng
[Phaser, ChFl2]
85: MM31: AmpSim – Tremolo
[AmpSim, Trml]
86: MM32: Reverb – Gate
[Reverb, Gate]
87: MM33: MicSim – Limiter
[MicSim, Lmtr]
154
Effects within multi-effect programs
MM1–MM33, and their parameters
Here are explanations of the parameters of each effect in the
multi-effect chains listed above.
P4EQ
(Parametric 4band EQ)
Fc1 (Band1 Cutoff [Hz]) .. 20Hz...1.0k Sets the center frequency of
Q1 (Q) ................................ 0.5...10.0 Sets the bandwidth of Band 1
G1 (Gain [dB]).................... –18...+18 Sets the gain of Band 1
Fc2 (Band2 Cutoff [Hz]) .. 50Hz...5.0k Sets the center frequency of
Q2 (Q) ................................ 0.5...10.0 Sets the bandwidth of Band 2
G2 (Gain [dB]).................... –18...+18 Sets the gain of Band 2
Fc3 (Band3 Cutoff [Hz])300Hz...10.0k Sets the center frequency of
Q3 (Q) ................................ 0.5...10.0 Sets the bandwidth of Band 3
G3 (Gain [dB]).................... –18...+18 Sets the gain of Band 3
Fc4 (Band4 Cutoff [Hz])500Hz...20.0k Sets the center frequency of
Q4 (Q) ................................ 0.5...10.0 Sets the bandwidth of Band 4
Gain4 (Gain [dB]) ............... –18...+18 Sets the gain of Band 4
Trim (Trim).............................. 0...100 Sets the parametric EQ input
Excit1
(Exciter1)
Blend (Exciter Blend) ..... –100...+100 Sets the intensity (depth) of the
Empha (Emphatic Point) ........ 0...140 Sets the frequency range to be
Excit2
(Exciter2)
This adds Pre LEQ and Pre HEQ to Exciter 1.
Blend (Exciter Blend) ..... –100...+100 Sets the intensity (depth) of the
Empha (Emphatic Point) ........ 0...140 Sets the frequency range to be
Trim (EQ Trim)........................ 0...100 Sets the EQ input level
LEQG (Pre LEQ Gain [dB]) –15...+15 Sets the gain of Low EQ
HEQG (Pre HEQ Gain [dB])–15...+15 Sets the gain of High EQ
Wah
(Wah/Auto Wah)
FcBtm (Frequency Bottom).... 0...100 Sets the lower limit of the wah
FcTop (Frequency Top) .......... 0...100 Sets the upper limit of the wah
*Mode (Sweep Mode)Auto, Pedal, LFO Selects the control from auto-
*Speed (LFO Frequency [Hz])............
0.02...20.0
Reso (Resonance) ................. 0...100 Sets the resonance amount
LPF (LPF) ..............................Off, On Switches the wah low pass filter
:Mode
Select "Pedal" if you wish to use an expression pedal to control the
wah.
Comp1
(Compressor1)
Sense (Sensitivity) ................. 1...100 Sets the sensitivity
Attack (Attack)........................ 1...100 Sets the attack level
Level (Output Level)............... 0...100 Sets the output level of the com-
Band 1
Band 2
Band 3
Band 4
level
Exciter effect
emphasized
Exciter effect
emphasized
center frequency
center frequency
wah, modulation source, and
LFO
Sets the LFO speed
on and off
pressor