Special Effect Se1 - Se4 - Korg D1600mkII Owner's Manual

Mix (Wet/Dry).... Dry, 1:99...99:1, Wet Sets the balance between the
: Pre LPF
If a sampler with a very low sampling frequency receives very high-
pitched sound that could not be heard during playback, it could gen-
erate pitch noise that is unrelated to the original sound. Set "Pre
LPF" to "On" to prevent this noise from being generated.
If you set the "Sampling Frequency" to about "3kHz" and set "Pre
LPF" to "Off," you can create a sound like a ring modulator.
: Resolution, : Output Level
If you set a smaller value for the "Resolution" parameter, the sound
may be distorted. The volume level may also be changed. Use "Out-
put Level" to adjust the level.
27: DY7: St.Parametric 4band EQ
(Stereo Parametric 4band EQ)
This is a stereo 4-band parametric equalizer. You can select peak-
ing type or shelving type for Band 1 and 4.
Trim (Trim)...............................0...100 Sets the input level
B1Type (Band1 Type)Peaking, ShelvL Selects the type of Band 1
B4Type (Band4 Type)Peaking, ShelvH Selects the type of Band 4
Fc1 (Band1 Cutoff [Hz]).......20...1.0k Sets the center frequency of
Q1 (Q).................................0.5...10.0 Sets the bandwidth of Band 1
G1 (Gain [dB]) ............. –18.0...+18.0 Sets the gain of Band 1
Fc2 (Band2 Cutoff [Hz]).....50...10.0k Sets the center frequency of
Q2 (Q).................................0.5...10.0 Sets the bandwidth of Band 2
G2 (Gain [dB]) ............. –18.0...+18.0 Sets the gain of Band 2
Fc3 (Band3 Cutoff [Hz])...300...10.0k Sets the center frequency of
Q3 (Q).................................0.5...10.0 Sets the bandwidth of Band 3
G3 (Gain [dB]) ............. –18.0...+18.0 Sets the gain of Band 3
Fc4 (Band4 Cutoff [Hz])...500...20.0k Sets the center frequency of
Q4 (Q).................................0.5...10.0 Sets the bandwidth of Band 4
G4 (Gain [dB]) ............. –18.0...+18.0 Sets the gain of Band 4
Mix (Wet/Dry).... Dry, 1:99...99:1, Wet Sets the balance between the
: Band1 Type, : Band4 Type
Selects a filter type for Band 1 and 4.
Special Effect SE1 – SE4
Category: Special Effect
28: SE1: St.Ring Modulator
(Stereo Ring Modulator)
This effect creates a metallic sound by applying the oscillators to
the input signal.
LPFLvl (Pre LPF)....................0...100 Sets the damping amount of the
Fc (Fixed Frequency [Hz]) ...0...12.0k Sets the oscillator frequency
Speed (LFO Frequency [Hz]).............
0.02...20.0
Depth (LFO Depth) .................0...100 Sets the depth of LFO modula-
Mix (Wet/Dry).... Dry, 1:99...99:1, Wet Sets the balance between the
: Pre LPF
This parameter enables you to set the damping amount of the high
range sound input to the ring modulator. If the input sound contains
lots of harmonics, the effect may sound dirty. In this case, cut a cer-
tain amount of high range.
144
effect and dry sounds
Band 1
Band 2
Band 3
Band 4
effect and dry sounds
high range input to the ring mod-
ulator
when OSC Mode is set to Fixed
Sets the LFO speed of the oscil-
lator frequency modulation
tion for the oscillator frequency
effect and dry sounds
: Fixed Frequency [Hz]
This parameter sets the oscillator frequency.
29: SE2: Doppler
This effect simulates the "Doppler effect" of a moving sound
with a changing pitch, similar to the siren of an passing ambu-
lance. Mixing the effect sound with the dry sound will create a
unique chorus effect.