Delay Dl1 - Dl6 - Korg D1600mkII Owner's Manual

5: RV5: Reverb Room
This room-type reverb emphasizes the early reflections that
make the sound tighter. Changing the balance between the early
reflections and reverb sound allows you to simulate nuances,
such as the type of walls of a room.
6: RV6: Bright Room
This room-type reverb emphasizes the early reflections that
make the sound brighter.
Time (Reverb Time [sec]) .....0.1...3.0 Sets the reverberation time
HiDamp (High Damp [%]) .......0...100 Sets the damping amount in the
PreDly (Pre Delay [msec]) ......0...200 Sets the delay time from the dry
Thru (Pre Delay Thru [%]).......0...100 Sets the mix ratio of non-delay
ERLvl (ER Level) ....................0...100 Sets the level of early reflections
RvbLvl (Reverb Level) ............0...100 Sets the reverberation level
EQTrim (EQ Trim) ...................0...100 Sets the EQ input level
LEQG (Pre LEQ Gain [dB]) –15...+15 Sets the gain of Low EQ
HEQG (Pre HEQ Gain [dB])–15...+15 Sets the gain of High EQ
Mix (Wet/Dry).... Dry, 1:99...99:1, Wet Sets the balance between the
: ER Level, : Reverb Level
These parameters set the early reflection level and reverb level.
Changing these parameter values allows you to simulate the type of
walls in the room. That is, a larger "ER Level" simulates a hard wall,
and a larger "Reverb Level" simulates a soft wall.
7: RV7: Early Reflection
This effect is only the early reflection part of a reverberation
sound, and adds presence to the sound. You can select one of the
four decay curves.
Type (Type) ................. Sharp, Loose,
Modula, Revers
ERTime (ER Time [msec]) ....10...800 Sets the time length of early
PreDly (Pre Delay [msec]) ......0...200 Sets the time taken from the orig-
EQTrim (EQ Trim) ...................0...100 Sets the input level of EQ applied
LEQG (Pre LEQ Gain [dB]) .............–
15.0...+15.0
HEQG (Pre HEQ Gain [dB]) ............–
15.0...+15.0
Mix (Wet/Dry).... Dry, 1:99...99:1, Wet Sets the balance between the
: Type
This parameter selects the decay curve for the early reflection.
Delay DL1 – DL6
Category: Delay-type effects
8: DL1: L/C/R Delay
This multitap delay outputs three Tap signals to the left, right,
and center respectively. You can also adjust the left and right
spread of the delay sound.
LTime (L Delay Time [msec]) 0...1360 Sets the delay time of TapL
LLevel (Level) ...........................0...50 Sets the output level of TapL
CTime (C Delay Time [msec])0...1360 Sets the delay time of TapC
CLevel (Level)...........................0...50 Sets the output level of TapC
RTime (R Delay Time [msec])0...1360 Sets the delay time of TapR
RLevel (Level)...........................0...50 Sets the output level of TapR
138
high range
sound
sound
effect and dry sounds
Selects the decay curve for the
early reflection
reflection
inal sound to the first early reflec-
tion
to the effect sound
Sets the gain of Low EQ
Sets the gain of High EQ
effect and dry sounds
Fdback (Feedback (C Delay)) ......... –
100...+100
HiDamp (High Damp [%]) ...... 0...100 Sets the damping amount in the
LoDamp (Low Damp [%])....... 0...100 Sets the damping amount in the
Spread (Spread) ...................... 0...50 Sets the width of the stereo
Mix (Wet/Dry) ....Dry, 1:99...99:1, Wet Sets the balance between the
: High Damp [%], : Low Damp [%]
These parameters set the damping amount of high range and low
range. The tone of the delayed sound becomes darker and lighter as
it feeds back.
: Spread
This parameter sets the pan width of the effect sound. The stereo
image is widest with a value of "50," and the effect sound of both
channels is output from the center with a value of "0."
9: DL2: St/Cross Delay
This is a stereo delay, and can by used as a cross-feedback delay
effect in which the delay sounds cross over between the left and
right by changing the feedback routing.
Mode (Stereo/Cross) .. Stereo, Cross Switches between stereo delay
LTime (L Delay Time [msec]) . 0...680 Sets the delay time for the left
RTime (R Delay Time [msec]) 0...680 Sets the delay time for the right
LFback (L Feedback) ..... –100...+100 Sets the feedback amount for the
RFback (R Feedback) .... –100...+100 Sets the feedback amount for the
HiDamp (High Damp [%]) ...... 0...100 Sets the damping amount in the
LoDamp (Low Damp [%])....... 0...100 Sets the damping amount in the
Spread (Spread) ................ –50...+50 Sets the width of the stereo
Mix (Wet/Dry) ....Dry, 1:99...99:1, Wet Sets the balance between the
10: DL3: St.Multitap Delay
The left and right Multitap Delays have two taps respectively.
Changing the routing of feedback and tap output allows you to
create various patterns of complex effect sounds.
Mode (Mode) .........Normal, X.Fback,
X.Pan1, X.Pan2
T1Time (Tap1 Time [msec]) ... 0...680 Sets the Tap1 delay time
T2Time (Tap2 Time [msec]) ... 0...680 Sets the Tap2 delay time
T1Lvl (Tap1 Level) ................. 0...100 Sets the Tap1 output level
Fdback (Feedback) ........ –100...+100 Sets the Tap2 feedback amount
HiDamp (High Damp [%]) ...... 0...100 Sets the damping amount in the
LoDamp (Low Damp [%])....... 0...100 Sets the damping amount in the
Spread (Spread) ............ –100...+100 Sets the width of the stereo
Mix (Wet/Dry) ....Dry, 1:99...99:1, Wet Sets the balance between the
: Mode
The left/right panning of the delay can be modified by changing the
connections of the left and right delay. Be aware that different
sounds must be input to the left and right channels in order for this
parameter to be effective.
: Tap1 Level
This parameter sets the output level of Tap1. Setting a different level
from Tap2 will add a unique touch to a monotonous delay and feed-
back.
Sets the feedback amountof
TapC
high range
low range
image of the effect sound
effect and dry sounds
(Stereo/Cross Delay)
and cross-feedback delay
channel
channel
left channel
right channel
high range
low range
image of the effect sound
effect and dry sounds
(Stereo Multitap Delay)
Switches the left and right delay
routing
high range
low range
image of the effect sound
effect and dry sounds