Needle Up/Down Compensation Switch; On/Off Switch Of The Material Edge Sensor; Automatic Thread Trimming Switch; One-Shot Automatic Stitching Switch - JUKI IP-110 Instruction Manual

5-6. Needle up/down compensation switch

1
5-7. ON/OFF switch
1

5-8. Automatic thread trimming switch

1

5-9. One-shot automatic stitching switch

1
Every­ time­ needle­ up/down­ compensation­ switch­ 1 ­ is­
pressed,­the­needle­goes­up­when­it­is­in­its­lowest­position­
or­ comes­ down­ when­ it­ is­ in­ its­ highest­ position.­ This­
compensates­the­stitch­by­a­half­of­the­predetermined­stitch­
length.
Note,­however,­that­the­machine­does­not­run­continuously­
at­a­low­speed­even­if­you­keep­the­switch­held­pressed.
Also,­note­that­the­needle­up/down­compensation­switch­is­
inoperative­after­turning­the­handwheel­by­hand.
Thread­ trimming­ is­ operative­ only­ at­ the­ time­ of­ stitch­
compensation­ after­ depressing­ the­ front­ part­ of­ the­ pedal­
once.
of the material edge sensor
•­When­material­edge­sensor­ 1 ­is­pressed,­ON/OFF­of­the­material­edge­
sensor­is­changed­over.
•­When­ the­ material­ edge­ sensor,­ which­ is­ optionally­ available,­ is­
connected­ to­ the­ operation­ panel,­ the­ ON/OFF­ switch­ of­ the­ material­
edge­sensor­becomes­effective.
•­If­ the­ material­ edge­ sensor­ is­ specified,­ the­ sewing­ machine­ will­
automatically­ stop­ running­ or­ perform­ thread­ trimming­ when­ the­ sensor­
detects­the­material­edge.
If the material edge sensor is used in combination with
the operation panel, carefully read the Instruction Manual
for the material edge sensor beforehand.
•­When­ automatic­ thread­ trimming­ switch­ 1 ­ is­ pressed,­ ON/OFF­ of­ the­
automatic­thread­trimming­is­changed­over.
•­This­ switch­ is­ used­ to­ automatically­ actuate­ the­ thread­ trimmer­ in­ a­
process­ where­ the­ sewing­ machine­ automatically­ stops­ or­ when­ the­
material­edge­sensor­is­used.
­ (if­ the­ automatic­ reverse­ stitching­ (for­ end)­ is­ specified,­ the­ thread­
trimmer­ will­ actuate­ after­ the­ sewing­ machine­ completes­ the­ automatic­
reverse­stitching­(for­end).)
•­When­one-shot­automatic­stitching­switch­ 1 ­is­pressed,­ON/OFF­of­the­
one-shot­automatic­stitching­is­changed­over.
•­This­switch­is­used,­in­the­constant-dimension­stitching­mode,­rectangular­
stitching­ mode,­ or­ in­ the­ process­ where­ the­ material­ edge­ sensor­ is­
specified, to make the sewing machine automatically perform sewing at
the specified speed until the end of the process is reached only by driving
the­sewing­machine­once.
–­57­–