JUKI IP-110 Instruction Manual page 79

No. Item
2 Teaching­motion­ Selection­of­the­motion­when­pressing­the­teaching­switch
selection ­­­­0­:­Normal­(teaching­motion­with­teaching­+­separately­driven­
­­­­­­­­­needle­changeover)
­­­­­:­Teaching­motion­with­separately­driven­needle­changeover­
­­­­­­­­­only­(when­starting­teaching­motion,­it­is­not­necessary­to­
­­­­­­­­­press­the­teaching­switch.)
­­­­2­:­Teaching­motion­in­the­state­of­two­needles­is­prohibited.­
­­­­­­­­­(Set­the­state­to­the­separately­driven­needle­state­and­press­
­­­­­­­­­the­teaching­switch.)
*­Possible­to­set­when­selecting­the­head­of­LH-468­or­LH488.
3 Number­of­ This­function­selects­the­number­of­stitches­of­replay­when­perform-
stitches­of­ ing­ corner­ teaching­ (measurement­ of­ number­ of­ stitches­ of­ sepa-
teaching­replay rately­driven­needle­sewing)
­­­­0­:­Number­of­stitches­of­replay­corresponds­to­that­of­
­­­­­­­­­measurement.
­­­­­:­Number­of­stitches­of­replay­is­that­which­is­subtracted­one­
­­­­­­­­­stitch­from­number­of­stitches­of­measurement.
*­Possible­to­set­when­selecting­the­head­of­LH-468­or­LH488.
4 Left­bobbin­ When­connecting­IP-0,­this­function­stops/uses­left­bobbin­thread­
thread­counter­ counter­function.
function ­­­­0­:­Left­bobbin­thread­counter­is­stopped.
­­­­­:­Left­bobbin­thread­counter­is­used.
*­Possible­to­set­when­selecting­the­head­of­LH-468­or­LH488.
5 Right­bobbin­ When­ connecting­ IP-0,­ this­ function­ stops/uses­ right­ bobbin­
thread­counter­ thread­counter­function.
function ­­­­0­:­Right­bobbin­thread­counter­is­stopped.
­­­­­:­Right­bobbin­thread­counter­is­used.
*­Possible­to­set­when­selecting­the­head­of­LH-468­or­LH488.
6 Corner­teaching­ When­connecting­IP-0,­this­function­selects­the­switch­to­start­in-
start­switch­ corner­sewing­in­the­corner­pattern­sewing.
selection ­­­­0­:­No­function
­­­­­:­Left­needle­changeover­switch
­­­­2­:­Right­needle­changeover­switch
­­­­3­:­Teaching­switch
­­­­4­:­Optional­switch
­­­­5­:­Knee­switch­and­presser­lifting­switch
­­­­6­:­No­function­(do­not­set.)
*­ When­ selecting­ ­ :­ Left­ needle­ changeover­ switch,­ 2­ :­ Right­
needle­ changeover­ switch­ or­ 3­ :­ Teaching­ switch­ for­ in-corner­
changeover­switch,­be­sure­to­set­No.­­Separately­driven­needle­
changeover­function­(corner­pattern)­to­"0"­(function­invalid).
*­Possible­to­set­when­selecting­the­head­of­LH-468­or­LH488.
7 Presser­lifting­ When­connecting­knee­switch,­this­function­selects­stop/use­of­
switch­function­ automatic­presser­lifting­function­by­knee­switch.
selection ­­­­0­:­Automatic­presser­lifting­by­knee­switch­is­stopped.
­­­­­:­Automatic­presser­lifting­by­knee­switch­is­used.
*­Possible­to­set­when­selecting­the­head­of­LH-468­or­LH488.
*­When­using­this­function,­set­the­presser­lifting­switch­one­stitch­
­­compensating­function­(No.­06)­to­"0"­(function­invalid).
8 Grease-up­error­ When­grease-up­error­(E220­or­E22)­has­occurred,­the­error­is­re-
release leased­by­setting­the­value­to­.
­­­­0­:­Normal­state
1 : Grease-up error is released when turning ON the power next
­­­­­­­­­time.­(This­function­is­also­released­after­releasing­grease-up­
­­­­­­­­­error.)­
* When releasing grease-up error, be sure to execute grease-up.
*­It­is­possible­to­set­only­to­the­machine­heads­that­require­grease-
up­(LH-400­and­some­of­LH-3500­series)
Description
–­76­–
Panel­display
Setting­ Setting­
Standard­set­
level range
value
TCMD
2 0­to­2
TCRN
2 0­to­
L-TR
2 0­to­
R-TR
2 0­to­
A2-
2 0­to­6
F-FPL
2 0­to­
GN-CLR
2 0­to­
0
0


5
0
0