Operation Of Remote Control Unit - Marantz SR4400 User Manual

SCANNING THE CODE TABLE
OSD
POWER
OK
2.
SETUP/
TV VCR1 DSS/VCR2 DVD T.TONE
S-DIRECT AUTO
1
6.
TUNER CD TAPE CDR/MD
NIGHT CSII
4
DISPLAY M-CH ST
AUX AMP
7
3.
TV MAIN
CLEAR MEMO
2.
VOL. SLEEP MUTE VOL.
OSD MENU BASS TREBLE
1.
Switch on the appliance which should be
controlled.
2.
Press and hold down the function button for
appliance which should be controlled and
press SETUP until the indicator blinking
twice.
3.
Press the code 9 - 9 - 1.
The indicator will blink twice.
4.
Aim the remote control at the appliance and
slowly alternate between pressing POWER
and the function button for the appliance.
5.
Stop when the appliance turns off.
6.
Press SETUP once to lock in the code.
CHECKING THE CODE
OK
1.
POWER
SETUP/
T.TONE
3.
S-DIRECT AUTO
1
TV VCR1 DSS/VCR2 DVD
NIGHT CSII
4.
4
TUNER CD TAPE CDR/MD
DISPLAY M-CH ST
7
CLEAR MEMO
AUX AMP
2.
TV MAIN
VOL. SLEEP MUTE VOL.
BASS TREBLE
OSD MENU MODE
1.
Press and hold down the function button for
appliance which should be controlled and
press SETUP until the indicator blinking twice.
2.
Press the code 9 - 9 - 0.
The indicator will blink twice.
3.
To view the code for first digit, press 1 once.
Wait 3 seconds, count the indicator blinks
(e.g. 3 blinks = 3) and write down the number.
Note:
If a code digit is "0", the indicator will not blink.
4.
Repeat step 3 three more times for remaining
digits. Use 2 for the second digit, 3 for the
third digit, and 4 for the fourth digit.
8
RESETTING THE ALL CODE
MENU
POWER
MENU OFF
DTS
TV VCR1 DSS/VCR2 DVD 1.
2 3
EX/ES DSP
TUNER CD TAPE CDR/MD
5 6
STEREO 6.1CH IN
8 9
AUX AMP
A/D P.SCAN
0
2.
TV MAIN
1.
VOL. SLEEP MUTE VOL.
CHANNEL/SKIP
TUNE/SEARCH
OSD MENU
1.
Press and hold down the any function button
and press SETUP until the indicator blinking
twice.
2.
Press the code 9 - 8 - 1.
The indicator will blink twice.
Then, RC5400SR will return to the factory
preset code.
Note:
• After this procedure, the selected function button
is set initial code and other function buttons are
set initial code too.
Once you have found and the codes for your various
appliances, you may want to write them down here.
TV
MENU OFF
DTS
2 3
EX/ES DSP
5 6 VCR
STEREO 6.1CH IN
8 9
A/D P.SCAN
0
DSS
CHANNEL/SKIP
TUNE/SEARCH
DVD
DISP./RDS F.DIRECT
CD
TAPE
CDR
MD
OPERATION OF REMOTE CONTROL
UNIT
OSD MENU
REMOTE CONTROL
OK
The distance between the transmitter of the
SETUP/ MENU OFF
T.TONE
remote control unit and the IR SENSOR of the
S-DIRECT AUTO DTS
1 2 3
SR4400 should be less than about 5 meters. If the
NIGHT CSII EX/ES DSP
4 5 6
transmitter is pointed to a direction other than the
DISPLAY M-CH ST STEREO 6.1CH IN
7 8 9
IR SENSOR or if there is an obstacle between
CLEAR MEMO A/D P.SCAN
0
them, remote control may not be possible.
CHANNEL/SKIP
BASS TREBLE TUNE/SEARCH
Remote-controllable range
60°
Remote control unit (RC5400SR)
LOADING BATTERIES
The life of the batteries used with the remote
control unit is about 4 months with normal use.
Also be sure to replace batteries earlier when you
notice that they are getting weak.
1.
Remove the back cover.
2.
Insert the new batteries (AAA type) with
correct and polarity.
3.
Close until it clicks.
SR4400