Remote Control Operation; Function And Operation - Marantz SR4400 User Manual

n
Subwoofer Output
Connect this jack to the line level input of a
powered subwoofer. If an external subwoofer
amplifier is used, connect this jack to the
subwoofer amplifier input. If you are using two
subwoofers, either powered or with a 2 channel
subwoofer amplifier, connect a "Y" connector to
the subwoofer output jack and run one cable from
it to each subwoofer amplifier.
m
Preamp Outputs (L, R, SL, SR, SB, C)
Jacks for L (front left), R (front right), C (Center),
SL (surround left), SR (surround right) and SB
(surround back).
Use these jacks for connection to some external
power amplifiers.
,
6.1 CHANNEL INPUT
By connecting a DVD Audio player, SACD multi
channel player, or other component that has a
multi channel port, you can playback the audio
with 5.1 channel or 6.1 channel output.
.
Speaker outputs terminals
Six terminals are provided for the front left, front
right, front center, surround left, surround right
and surround back speakers.
⁄0
REMOTE CONT. IN/OUT terminals
Connect to a Marantz component equipped with
remote control (RC-5) terminals.
6
⁄1
DIGITAL INPUT (Dig.1 - 4) / OUTPUT
(coaxial, optical)
These are the digital audio inputs and outputs.
There are 2 digital inputs with coaxial jacks, 2 with
optical jacks.
The inputs accept digital audio signals from a
compact disc, LD, DVD, or other digital source
component.
For digital output, there is 1 coaxial output and 1
optical output.
The digital outputs can be connected to MD
recorders, CD recorders, DAT decks, or other
similar components.
⁄2
AC INLET
Plug the supplied power cord into this AC INLET
and then into the power outlet on the wall.
⁄3
AC OUTLET
Connect the AC power cables of components
such as a DVD and CD player to this outlet.
SWITCHED outlet is provided.
The marked SWITCHED provides power only
when the SR4400 is turned on and is useful for
components which you use every time you play
your system.
Cautions:
• In order to avoid potential turn-off thumps,
anything plugged in here should be powered up
before the SR4400 is turned on.
• The capacity of this AC outlet is 100W. Do not
connect devices that consume electricity more
than the capacity to this AC outlet. If total power
consumption of connected devices exceeds the
capacity, protection circuit shuts down the power
supply.
REMOTE CONTROL
OPERATION

FUNCTION AND OPERATION

The provided remote control unit is a universal re-
mote controller. The POWER button, numeric but-
tons and control buttons are used in common across
different input source components.
The input source controlled with the remote control
unit changes when one of the input selector but-
tons is pressed.
z
POWER
x
TV VCR1 DSS/VCR2 DVD
c
TUNER CD TAPE CDR/MD
AUX AMP
¤4 v
TV MAIN
VOL. SLEEP MUTE VOL.
¤3
b
¤2
n
OSD MENU
m
OK
¤1
,
SETUP/
MENU OFF
T.TONE
¤0
S-DIRECT AUTO DTS
1 2 3
⁄9
NIGHT CSII EX/ES DSP
4 5 6
.
⁄8
DISPLAY M-CH ST STEREO 6.1CH IN
7 8 9
⁄0
⁄7
CLEAR MEMO A/D P.SCAN
0
⁄6 ⁄1
CHANNEL/SKIP
⁄5
BASS TREBLE TUNE/SEARCH
⁄2
⁄4
MODE DISP./RDS F.DIRECT
+/A /ANT –/B /VCR ATT. PTY
⁄3
DISC/DECK
SYSTEM REMOTE CONTROLLER
RC5400SR
z
Transmitting indicator
Lights up during a button is pressed and an infrared
signal is sending.
x
(Main) POWER buttons
Press to switch the power of the SR4400 ON or OFF
after pressing the AMP button.
c
Input selector buttons/ FUNCTION
SELECTOR buttons (AUDIO/VIDEO INPUT)
These buttons are used to select a Audio or Video
source component. Press one of these buttons once
to change the function of the remote control. Press
same button within 2 seconds, the input function of
the SR4400 is changed.
Note:
• CDR/MD button is set CDR function at initial. To
switch MD function, press and hold down CDR/
MD button and press 2 button.
• To return CDR function, press and hold down
CDR/MD button and press 1 button.
• AUX button is unavailable for SR4400.
v
MAIN VOLUME UP ( ) /DOWN ( ) buttons
Main volume control of the SR4400. The front, sur-
round, center and subwoofer channel volumes con-
trolled by these buttons simultaneously.
b
MUTE button
Muting button of the SR4400. Press this button de-
crease the sound temporarily . Press this button
again to return to the previous sound.
When this button is pressed, "MUTE" indicator lights
up.
n
MENU button
This button is used to enter the SETUP MAIN MENU.
m
Cursor buttons ( , , , , OK)
Use these button when operating the SETUP MAIN
MENU.
See page 15.
,
MENU OFF button
This button is used to exit from the SETUP MAIN
MENU.