Midi Implementation - Roland SPD-S Owner's Manual

MIDI Implementation

Model SPD-S
Version 1.00
February.14 2003
1. Receive data
* In wave mode, the SPD-S receives no messages other than active sensing.
* MIDI messages received are not included in Phrase Maker data.
■Channel Voice Messages
* Following Channel Voice Messages can be recorded in SETUP/MIDI/MIDI
Channel.
●Note Off
Status 2nd byte
8nH kkH
9nH kkH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
kk = note number: 00H - 7FH (0 - 127)
vv = note off velocity: 00H - 7FH (0 - 127)
* The Velocity Values of Note Off message are ignored.
* For a wave in which the trigger mode is set to SHOT or ALT, Note Off messages
are ignored.
●Note On
Status 2nd byte
9nH kkH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
kk = note number: 00H - 7FH (0 - 127)
vv = note on velocity: 01H - 7FH (1 - 127)
* For a wave in which the trigger mode is set to ALT, a sound is alternately
generated and muted each time a Note On message is received.
●Control Change
* Not Received when SETUP/MIDI/CC TX/RX Switch is set to "OFF." (Initial
Value is ON)
❍Foot Control (Controller number 4)
Status 2nd byte
BnH 04H
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
vv = Control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON
* This is used as the data of the "WAVE SW" function of the Foot Switch.
❍Expression (Controller number 11)
Status 2nd byte
BnH 0BH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
vv = Control value: 00H - 7FH (0 - 127)
* This is used as the data of the Expression Pedal.
3rd byte
vvH
00H
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
❍Effect Control 1 (Controller number 12)
Status 2nd byte
BnH 0CH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
vv = Control value: 00H - 7FH (0 - 127)
* This is used as the data of the EFFECTS CONTROL knob.
❍Effect Control 2 (Controller number 13)
Status 2nd byte
BnH 0DH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
vv = Control value: 00H - 7FH (0 - 127)
* This is used as the data of the Velocity Control.
●Program Change
Status 2nd byte
CnH ppH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
pp = Program number: 00H - 7FH (prog.1 - prog.128)
* Not Received when SETUP/MIDI/PC TX/RX Switch is set to "OFF".(Initial
Value is ON)
* The sound will change beginning with the next note-on after the program
change is received. Waves with the Trigger mode set to "SHOT" and Loop set to
"OFF" that were already being played prior to reception of the program change
are not affected.
■Channel Mode Messages
* Following Channel Mode Messages can be received on channel specified in
SETUP/MIDI/MIDI Channel.
●All Sounds Off (Controller number 120)
Status 2nd byte
BnH 78H
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
* When this message is received, all currently-sounding notes will be silenced.
However, the status of channel messages will not change.
●Reset All Controllers (Controller number 121)
Status 2nd byte
BnH 79H
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
* When this message is received, the following controllers will be set to their reset
values.
Controller Reset value
Foot Control 0 (off)
Expression 0 (off)
Effect Control 1 0 (off)
Effect Control 2 0 (off)
3rd byte
vvH
3rd byte
vvH
3rd byte
00H
3rd byte
00H
119