Table of Contents
Advertisement
Quick Links
See also:
User Manual
OCTAPAD SPD-30 Effects List
The multi-effects feature 30 different kinds of effects.
Number
Effect Name
00
THRU
01
SUPER FILTER
02
STEP FILTER
03
FILTER+DRIVE
04
AUTO WAH
05
COMPRESSOR
06
LO-FI COMPRESS
07
DISTORTION
08
OVERDRIVE
09
EQUALIZER
10
ISOLATOR
11
SLICER
12
RING MODULATOR
13
STEP RINGMOD
14
PITCH SHIFT
15
STEREO DELAY
16
3TAP PAN DELAY
17
REVERSE DELAY
18
TAPE ECHO
19
CHORUS
20
HEXA-CHORUS
21
SPACE-D
22
PHASER
23
STEP PHASER
24
INFINITE PHASER
25
FLANGER
26
STEP FLANGER
27
AUTO PAN
28
ROTARY
29
REVERB
30
LONG REVERB
Copyright © 2010 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND
CORPORATION.
About Note Values
Some effect parameters (such as Rate or Delay Time) can
be set by using note values.
Whenever the "BPM Sync" parameter is set to "ON, " settings
can be made in terms of a note value, so when the effect
is applied, it will be synchronized to the tempo set for the
Kit or Phrase.
note:
Sixty-fourth-note triplet
Thirty-second-note triplet
Sixteenth-note triplet
Sixteenth note
Dotted sixteenth note
Quarter-note triplet
Quarter note
Dotted quarter note
Whole-note triplet
Whole note
Dotted whole note
When "BPM Sync" is set to "OFF, " a numerical value can be
set for the relevant items.
NOTE
If you set the delay time as a note value, slowing down
the tempo will not change the delay time beyond a
certain length. There is an upper limit for the delay
time so if it is set as a note value and you slow down
the tempo until this upper limit is reached, the delay
time cannot change any further. This upper limit is the
maximum value that can be specified when setting the
delay time as a numerical value.
About Knob Indications
When the icons shown below appear along with a
parameter in the FX-EDIT screen, it means that this FX
parameter can be controlled with the knobs in the FX
CONTROL screen. For each FX, the optimal parameters
have been assigned and made available for control.
Knob 1
Knob 2
Knob 3
Sixty-fourth note
Thirty-second note
Dotted thirty-second note
Eighth-note triplet
Eighth note
Dotted eighth note
Half-note triplet
Half note
Dotted half note
Double-note triplet
Double note
1PS
1
Advertisement
Table of Contents
Related Manuals for Roland SBX-1000
Summary of Contents for Roland SBX-1000
- Page 1 Knob 1 Knob 2 Knob 3 Copyright © 2010 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.
-
Page 2: Super Filter
00: THRU The effect won’t be applied. 01: SUPER FILTER This is a filter with an extremely sharp slope. The cutoff frequency can be varied cyclically. Knob Parameter Value Explanation Filter Type LPF, BPF, HPF, NOTCH Filter type Frequency range that will pass through each filter LPF: Frequencies below the cutoff BPF: Frequencies in the region of the cutoff HPF: Frequencies above the cutoff... -
Page 3: Step Filter
02: STEP FILTER This is a filter whose cutoff frequency can be modulated in steps. You can specify the pattern by which the cutoff frequency will change. Knob Parameter Value Explanation [Knob 3] Cutoff Modify -64–+63 Increases/decreases value for all steps Cutoff Step 1-8 0–127 Cutoff frequency at each step... - Page 4 04: AUTO WAH Cyclically controls a filter to create cyclic change in timbre. Knob Parameter Value Explanation Filter Type LPF, BPF Type of filter LPF: The wah effect will be applied over a wide frequency range. BPF: The wah effect will be applied over a narrow frequency range. [Knob 3] Manual 0–127...
- Page 5 06: LO-FI COMPRESS This is an effect that intentionally degrades the sound quality for creative purposes. Knob Parameter Value Explanation Pre Filter Type 1–3 Selects the type of filter applied to the sound before it passes through the Lo-Fi effect. Lo-Fi Type 1–9 Degrades the sound quality.
- Page 6 08: OVERDRIVE Mildly distorts the sound. The tone quality of the distorted sound is adjusted with a filter. Knob Parameter Value Explanation Pre HPF BYPASS, 16–1000 Hz Frequency of the filter that cuts the low-frequency content of the input sound (BYPASS: no cut) [Knob 1] Drive...
- Page 7 10: ISOLATOR This is an equalizer which cuts the volume greatly, allowing you to add a special effect to the sound by cutting the volume in varying ranges. Knob Parameter Value Explanation [Knob 1] Boost/Cut Low -64–+63 These boost and cut each of the Low frequency ranges. At -64, the sound becomes inaudible.
-
Page 8: Ring Modulator
12: RING MODULATOR This is an effect that applies amplitude modulation (AM) to the input signal, producing bell-like sounds. You can also change the modulation frequency in response to changes in the volume of the sound sent into the effect. Knob Parameter Value... -
Page 9: Pitch Shift
14: PITCH SHIFT Shifts the pitch of the original sound. This pitch shift can add two pitch shifted sounds to the original sound. Knob Parameter Value Explanation [Knob 1] Pitch 1 [semitone] -24–+12 semi Adjusts the pitch of Pitch Shift 1 in semitone steps. [Knob 2] Pitch 2 [semitone] -24–+12 semi... -
Page 10: Stereo Delay
15: STEREO DELAY This is a stereo delay. Knob Parameter Value Explanation Left BPM Sync OFF, ON OFF: Left Time specified as numerical value ON: Left Time specified as note value Left Time 0–1300 msec, note Adjusts the time until the delay sound is heard. Right BPM Sync OFF, ON OFF: Right Time specified as numerical value... -
Page 11: Reverse Delay
17: REVERSE DELAY This is a reverse delay that adds a reversed sound of the input sound as a delayed sound. A chorus is connected immediately after the reverse delay. Knob Parameter Value Explanation Threshold 0–127 Volume at which the reverse delay will begin to be applied Reverse Delay BPM OFF, ON OFF: Reverse Delay Time specified as numerical value... - Page 12 19: CHORUS This is a stereo chorus. A filter is provided so that you can adjust the timbre of the chorus sound. Knob Parameter Value Explanation Filter Type OFF, LPF, HPF Type of filter OFF: no filter is used LPF: cuts the frequency range above the Cutoff Freq HPF: cuts the frequency range below the Cutoff Freq Cutoff Frequency 200–8000 Hz...
- Page 13 21: SPACE-D This is a multiple chorus that applies two-phase modulation in stereo. It gives no impression of modulation, but produces a transparent chorus effect. Knob Parameter Value Explanation Pre Delay 0.0–100 msec Adjusts the delay time from the direct sound until the chorus sound is heard. Rate BPM Sync OFF, ON OFF: Rate specified as numerical value...
-
Page 14: Step Phaser
23: STEP PHASER This is a stereo phaser. The phaser effect will be varied gradually. Knob Parameter Value Explanation Mode 4-STAGE, 8-STAGE, Number of stages in the phaser 12-STAGE [Knob 2] Manual 0–127 Adjusts the basic frequency from which the sound will be modulated. Rate BPM Sync OFF, ON OFF: Rate specified as numerical value... -
Page 15: Step Flanger
25: FLANGER This is a stereo flanger. (The LFO has the same phase for left and right.) It produces a metallic resonance that rises and falls like a jet airplane taking off or landing. Knob Parameter Value Explanation Pre Delay 0.0–100 msec Adjusts the delay time from when the direct sound begins until the flanger sound is heard. - Page 16 27: AUTO PAN Cyclically modulates the stereo location of the sound. Knob Parameter Value Explanation Rate BPM Sync OFF, ON OFF: Rate specified as numerical value ON: Rate specified as note value [Knob 1] Rate 0–127, note Frequency of the change [Knob 2] Depth 0–127...
- Page 17 29: REVERB Choose between 4 different types of basic reverbs. Knob Parameter Value Explanation Reverb Type ROOM1, ROOM2, Type of reverb STAGE1, STAGE2 ROOM1: dense reverb with short decay ROOM2: sparse reverb with short decay STAGE1: reverb with greater late reverberation STAGE2: reverb with strong early reflections Pre Delay 0.0–100 msec...
-
Page 18: Long Reverb
30: LONG REVERB This is a very rich sounding reverb with a choice of 6 types. Knob Parameter Value Explanation [Knob 1] Depth 0–127 Depth of the effect [Knob 2] Reverb Time 0–127 Time length of reverberation Character 0–5 Type of reverb Pre LPF 16–15000 Hz, BYPASS Frequency of the filter that cuts the high-frequency content of the input sound...