Craftsman 113.221620 Owner's Manual page 3

for recommended accessories. The use of
improper accessories may cause risk of injury
to persons.
2. Choose the right blade or cutting accessory
for the material and the type of cutting you
plan to do.
3. Never use grinding wheels, abrasive cut-off
wheels, friction wheels (metal slitting
blades) wire wheels or buffing wheel. They
can fly apart explosively.
4. Choose and inspect your cutting tool carefully.
a. To avoid cutting tool failure and thrown
shrapnel (broken pieces of blade), use only
8" or smaller blades or other cutting tools
marked for speeds of 3450 rpm or higher.
b. Always use unbroken, balanced blades
designed to fit this saw's 5/8" arbor.
c. When thru-sawing, (making cuts where the
blade comes through the workpiece top)
always use a 8" diameter blade. This keeps
the spreader in closest to the blade.
d. Do not overtighten arbor nut. Use arbor
wrenches to "snug" it securely.
e. Use only sharp blades with properly set
teeth. Consult a professional blade shar-
pener when in doubt.
f. Keep blades clean of gum and resin.
5. Adjust table inserts flush with the table top.
NEVER use the saw without the proper insert.
6. Make sure all clamps and locks are tight and no
parts have any excessive play.
2. KEEP WORK AREA CLEAN
a. Cluttered areas and benches invite accidents.
Floor must not be slippery from wax or
sawdust.
b. To avoid burns or other fire damage, never use
the saw near flammable liquids, vapors or
gases.
Plan ahead to protect your eyes, hands, face,
ears.
a. To avoid injury, don't do layout, assembly, or
setup work on the table while the blade is
spinning. It could cut or throw anything hitting
the blade.
AVOID ACCIDENTAL STARTING - Make sure
switch is "OFF" before plugging saw in.
Plan your work
1. USE THE RIGHT TOOL - Don't force tool or
attachment to do a job it was not designed for.
2. Dress for safety:
- Do not wear loose clothing, gloves, neckties
or jewelry (rings, wrist watches). They can get
caught and draw you into moving parts.
- Wear nonslip footwear.
- Tie back long hair.
- Roll long sleeves above the elbow
Noise levels vary widely. To avoid possible
hearing damage, wear ear plugs or muffs
when using saw for long periods of time.
Any power saw can throw foreign objects into
the eyes. This can cause permanent eye
damage. Wear safety goggles (not glasses)
that comply with ANSI Z87.1 (shown on pack-
age). Everyday eyeglasses have only impact
resistant lenses. They are not safety glasses.
Safety goggles are available at Sears retail
catalog stores. Glasses or goggles not in
compliance with ANSI Z87.1 could seriously
hurt you when they break.
WEAR YOUR
- For dusty operations, wear a dust mask along
with the safety goggles.
3. Inspect your workpiece. Make sure there are no
nails or foreign objects in the part of the work-
piece to be cut.
4. Plan yourcut to avoid KICKBACKS and THROW-
BACKS - when a part or all of the workpiece
binds on the blade and is thrown violently back
toward the front of the saw:
- Never cut FREEHAND: Always use either a rip
fence, miter gauge or fixture to position and
guide the work, so it won't twist, bind on the
blade and kickback.
-Make sure there's no debris between the
workpiece and its supports.
- When cutting irregularly shaped workpieces,
plan your work so it will not slip and pinch the
blade:
- A piece of molding, for example, must lie
flat or be held by a fixture or jig that will not
let it twist, rock or slip while being cut. Use
jigs, fixtures where needed to prevent work-
piece shifting.
- Use a different, better suited type of tool for
work that can't be made stable.
- Use extra caution with large, very small or
awkward workpieces:
-Use extra supports (tables, saw horses,
blocks, etc.) for any workpieces large
enough to tip when not held down to the
table top. NEVER use another person as a
substitute for a table extension, or as addi-
tional support for a workpiece that is longer
or wider then the basic saw table, or to help
feed, support or pull the workpiece.
- Never confine the piece being cut off. That
is, the piece NOT against the fence, miter
gauge or fixture. Never hold it, clamp it,
touch it, or use length stops against it. It
must be free to move. If confined, it could
get wedged against the blade and cause a
kickback or throwback.