Table of Contents
Advertisement
Quick Links
ISears i
owners
manual
MODEL NO.
113.23112
Serial
Number
Model and serial
number
may be found
at the rear left-hand side
of the base.
You should record both
model and serial number
in a safe place for
future use.
CAUTION:
Read
GENERAL
and
ADDITIONAL
SAFETY
INSTRUCTIONS
carefully
[RRFTSMRN°
IO-INCH
RADIAL
SAW
• assembly
• operating
• repair
parts
Sold
by SEARS,
ROEBUCK
AND
CO.,
Chicago,
IL. 60684
U.S.A.
Part
No.
63770
Printed
in U.SA.
Advertisement
Table of Contents
Related Manuals for Craftsman 113.23112
Summary of Contents for Craftsman 113.23112
- Page 1 ISears i owners manual MODEL NO. 113.23112 Serial Number Model and serial number may be found at the rear left-hand side of the base. You should record both [RRFTSMRN° model and serial number in a safe place for future use. IO-INCH CAUTION: RADIAL...
- Page 2 FULL ONE YEAR WARRANTY ON CRAFTSMAN RADIAL SAWS If within one year from the date of purchase, this Craftsman Radial Saw fails due to a defect in material workmanship, Sears will repair it, free of charge. Warranty service is available...
- Page 3 additional safety instructions for radial saws SAW) BECOME COMMONPLACE. ALWAYS CAUTION: Always disconnect power cord before REMEMBER THAT A CARELESS FRACTION removing the guard, changing the cutting tool, changing A SECOND IS SUFFICIENT TO INFLICT SEVERE set-up making adjustments. Shut motor before INJURY.
- Page 4 additional safety instructions for radial saws support or guide the workpiece, to prevent rotating slippery, anti-kickback pawls stop twisting of the workpiece during the operation. kickback Never "RIP" in the crosscut position. Never make Therefore, rip with the finished side down (next miter cut with...
- Page 5 additional safety instructions for radial saws WEAR YOUR operation power tool result foreign objects being thrown into eyes, which can result severe eye damage. Always wear safety goggles complying with ANSI Z87.1 (shown on Package) before commencing power tool operation. Safety Goggles are available...
- Page 6 Nut, Lock, 5/16-18 ....Twin nut (for attaching rip-scale indicator) Nut, Speed ......REMOVE SKIDS FROM BASE MOUNT SAW TO CRAFTSMAN BASE LEG SET, OR FLAT BENCH {NOT SUPPLI ED IN CANADA) Make sure elevation crank is free to rotate.
- Page 7 ATTACH ELEVATION CRANK. Be sure setscrew is tightened on flat of shaft. ELEVATE TO ITS MAX. HEIGHT. Remove shipping block. INJ'O RMAT LOCKWASHER REMOVE CARRIAGE STOP SCREW, TAG. Read warning tag before discarding. STOP SCREV, SUPPL![D TIGHTEN LOCK KNOB BEFORE PROCEEDING.
- Page 8 Set aside and out of the way. ALIGNMENTPROCEDURE The following STEP alignment procedure will bring accuracy which is built in every CRAFTSMAN tool. The secret best results is in knowing to set up the tool and keep it in good alignment. BE SURE...
- Page 9 3. Loosen armlockknobuntilarm isfree tomove. Note: In accordance with the UL standard, stops have been provided to prevent 360 ° rotation of the radial arm. Loosen carriage lock knob position against stop {approximately 50 ° Miter) and carriage directly over the center of left hand channel.
- Page 10 unpacking and assembly LATCH LEVER Position at approximately 30 ° miter setting lock lock knob. Loosen lock knob turn and index at 0 ° miter setting. Push the arm latch solidly with palm of hand this will seat the arm index pin properly.
- Page 11 marked tooth moves into the square when moving blade from the rear toward the front of the table, tap the left hand front edge of the table with a mallet shown (Loosen table attaching screws slightly necessary). If the marked tooth moves away from...
- Page 12 unpacking and assembly INSTALLING REMAINING REAR TABLE BOARDS• Position (guide) fence, spacer board and rear table board behind the front table board, as shown. Install table clamps in the slots provided them at the rear the saw base, and tighten them securely.
- Page 13 To correct for either type of "heel" or "toe" condition proceed as follows: Remove left hand carriage cover. Loosen the yoke clamp handle. Loosen (slightly) the two hex-head screws• Rotate yoke assembly until gap between saw blade and square is eliminated. Lock yoke clamp...
- Page 14 unpacking and assembly ;ai' With the fence in its normal position (next to front table), loosen yoke clamp handle, lift up on swivel latch knob and rotate the yoke as shown to index the yoke 90 ° from the cross cut position. This will locate...
- Page 15 Carriage Lock Depth of Cut carriage lock knob is rotated clockwise diagram shows elevation crank which used to raise and lower the saw blade. secure carriage radial arm, counterclockwise to release it. Clockwise rotation raises blade When performing a square or miter-angle crosscut, counterclockwise...
- Page 16 If the pawls do not catch, readjust. PRECISION INDEXING Experienced operators of precision equipment, such as this SCREW Craftsman Radial Saw, normally acquire habit (1/4-20x I/2 IN., HLX-HD) indexing machine in one direction only, whenever...
- Page 17 basic saw operations Basi( saw operations are summarized into six categories, explained illustrated following paragraphs_ manual entitled "The Radial Saw" is available at your nearest Sears Retail Store or Catalog Order House. This manual contains considerable data project ideas applicable to the radial saw.
- Page 18 basic saw operations OPERATION No. 2 - MITER CROSSCUT Miter crosscutting is the process of sawing a board at any angle other than a 90 ° (square) cut. The 45 ° miter angle is a popular one, since boards 45 ° assembled to form a 90 °...
- Page 19 F:'JSH ST ICh REQUIREMENTS WHEN RIPPING (I_FNCH SL_L!ARES) (OPERATIONS 5 AND PUSH STICK Carriage lock knob must be tight. Radial arm must be locked in 0 ° position. Work must be held firmly against table and fence while feeding through. Guard and anti-kickback mechanism...
- Page 20 basic saw operations Since the work is pushed along the fence, it must have a reasonably straight edge order make sliding contact with the fence. Also, the work must make solid contact with table, so that it will wobble. Provide a straight edge, even...
- Page 21 electrical connections POWER SUPPLY is recommended that have a qualified electrician replace the TWO prong outlet with a properly grounded Motor Specifications THREE prong outlet. motor used this saw is a capacitor-start, adapter as shown below is available for connecting plugs non-reversible type...
- Page 22 Even' though finest materials precision LOOSENESS COLUMN TUBE COLUMN workmanship have been incorporated into your Craftsman SUPPORT ELEVATION CRANK OPERATES saw, it is reasonable to expect some wear after long periods ROUGHLY OR CHATTERS WHEN ROTATED. of use. Sooner or later,...
- Page 23 SAW CUTS ANGLE 90 ° TO TABLE TOP. Table support channels not properly leveled. Refer Step under Alignment Procedure i(::!L[ [,E 90 _ Section. \/// Blade not square to work table top. S,_J Refer to Step four in Alignment Procedure Section.
- Page 24 trouble-shooting CARRIAGE BEARINGS LOOSE. test for looseness between bearings and tracks radial arm, perform the following steps, Remove left-hand carriage cover. Push the carriage to its full most rearward position. Finger hold front carriage bearing as shown apply as much force as possible and at the same...
- Page 25 MOTOR TROUBLE - SHOOTING CHART NOTE: Motors used on wood working tools are particularly susceptible to the accumulation of sawdust and wood chips should be blown "vacuumed" frequently prevent interference with normal motor ventilation. SUGGESTED REMEDY PROBABLE CAUSE TROUBLE Motor will not run.
- Page 26 "OFF" REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE MAINTAINING LUBRICATING YOUR SAW. When receive your Craftsman radial saw, requires no lubrication. radial saw has been partially aligned and all bearings are lubricated and sealed for life. time, however, order keep...
- Page 27 recommended accessories IN CANADA, SEE YOUR LOCAL SIMPSONS-SEARS STORE OR CATALOG FOR ACCESSORY SELECTION NUMBERS ITEM CAT.NO. Stand ........9-22202 Steel Legs ....... 9-22238 Castors ......9-22201 - 9 22209 Key Chuck ....... 9-2980 * Molding Head Guard 7-Inch ....9-29524 *Molding Head Guard...
- Page 28 PARTS LIST FOR CRAFTSMAN 10-INCH RADIAL MODEL NUMBER 113.23112 " .. 28 27 3| 29 Figure 1...
- Page 29 PARTS LIST FOR CRAFTSMAN 10-INCH RADIAL MODEL NUMBER 113.23112 All parts illustrated in Figures 1 through 5 and listed under part numbers may be ordered through any Sears retail mail order store. Order parts by mail from the catalog order...
- Page 30 PARTS LIST FOR CRAFTSMAN 10-INCH RADIAL MODEL NUMBER 113.23112 "0 it" 11t/ 3938 "\ -.------41 _-------42 !_._._-------36 46---_ _"_45...
- Page 31 PARTS LIST FOR CRAFTSMAN 10-INCH RADIAL MODEL NUMBER 113.23112 FIGURE Part Part Description Description STD 541431 Nut, Lock, 5/16 STD 523106 _Screw, Mach.Hex.lnd.Hd.,5/16-18 x 1/2 37887 Wrench, Hex. "L", STD 551131 * Lockwasher, 5/16 STD 502503 *Screw, Set, 1/4-20 x 3/8,Soc.Hd.Cup...
- Page 32 C_-.-- PARTS LIST FOR CRAFTSMAN 10-INCH RADIAL MODEL NUMBER 113.23112 ,,----__,._ 23 24 Figure...
- Page 33 PARTS LIST FOR CRAFTSMAN 10-INCH RADIAL MODEL NUMBER 113.23112 FIGURE Part Description Description 63534 Cord with Plug 63507 Motor (See Figure 63467 Cap, Flag Terminal STD 541231 *Nut, Hex 5/16-18 x 1/2x 3/16 60267 Switch, Locking 114605 *Lockwasher, External Tooth,...
- Page 34 PARTS LIST FOR CRAFTSMAN 10-INCH RADIAL MODEL NUMBER 113.23112 ,,,-IP OANY ATTEMPT TO REPAIR THIS MOTOR MAY CREATE A HAZARD UNLESS REPAIR IS DONE BY A QUALIFIED SERVICE TECHNICIAN. REPAIR SERVICE IS AVAILABLE AT YOUR NEAREST SEARS STORE. FIGURE 4 - 63605 MOTOR...
- Page 35 PARTS LIST FOR CRAFTSMAN 10-INCH RADIAL MODEL NUMBER 113.23112 FIGURE GUARD ASSEMBLY Part Description 63537 Guard 63541 Bar, Anti-Kickback 63540 Guide, Anti-Kickback 60136 *Washer. 13/64 x 5/8 x 1/32 STD 601103 *Screw, Type T Pan Hd., 10-32 x 3/8 60219...
- Page 36 ISearsi owners IO-INCH RADIAL SAW manual SERVICE Now that you have purchased your 10 inch radial saw, should a need ever exist for repair parts or service, simply contact Sears Service Center and most Sears, Roebuck and Co. stores. Be sure to provide all pertinent facts when you call or visit.