System Log: Entire - Netopia 2200 series Software User's Manual

Link:

System Log: Entire

The system log shows the state of the WAN connection as well as the PPPoE session. Ver-
ify that the PPPoE session has been correctly established and there are no failures. If
there are error messages, go to the WAN configuration and verify the settings. The follow-
ing is an example of a successful connection:
Message Log:
00:00:00:00 L3
00:00:00:00 L3
00:00:00:00 L3
00:00:00:00 L4
00:00:00:00 L4
00:00:00:00 L4
00:00:00:00 L4
00:00:00:00 L4
00:00:00:00 L3
00:00:00:00 L3
00:00:00:00 L4
00:00:00:00 L3
00:00:00:00 L4
00:00:00:00 L3
00:00:00:00 L3
00:00:00:00 L3
00:00:00:00 L3
00:00:00:00 L4
00:00:00:00 L4
00:00:00:00 L4
00:00:00:00 L3
00:00:00:00 L3
00:00:00:00 L3
00:00:00:00 L3
00:00:00:00 L3
00:00:00:00 L3
.
.
.
00:00:00:24 L4
00:00:00:25 L3
00:00:00:25 L3
00:00:00:25 L3
00:00:00:25 L3
00:00:00:25 L3
00:00:00:25 L3
00:00:00:25 L3
00:00:00:25 L3
00:00:00:25 L3
00:00:00:25 L3
00:00:00:25 L3
00:00:00:25 L3
00:00:00:25 L3
00:00:00:25 L3
00:00:00:25 L3
00:00:00:25 L3
00:00:00:25 L3
00:00:00:25 L3
00:00:00:25 L3
00:00:00:25 L3
00:00:00:25 L3
00:00:00:25 L3
00:00:00:25 L3
00:00:00:25 L3
00:00:00:27 L3
7/16/03 01:55:31 PM L4
7/16/03 01:55:33 PM L4
7/16/03 01:55:33 PM L4
214
KS: Using configured options found in flash
BOOT: Warm start v7.3r0 ----------------------------------
IP address server initialization complete
BR: Using saved configuration options
BR: Netopia SOC OS version 7.3.0 (build r0)
BR: Netopia-3000/9495032 (Netopia-3000, rev 1), PID 1205
BR: last install status: Firmware installed successfully
BR: memory sizes - 2048K Flash, 8192K RAM
BR: Starting kernel
AAL5: initializing service
ATM: Waiting for PHY layer to come up
POE: Initializing PPP over Ethernet service
POE: Binding to Ethernet (ether/vcc1)
BRDG: Configuring port (10/100BT-LAN)
BRDG: Bridge not enabled for WAN.
BRDG: Bridging from one WAN port to another is disabled
BRDG: Initialization complete
IP: Routing between WAN ports is disabled
IP: IPSec client pass through is enabled
IP: Address mapping enabled on interface PPP over Ethernet vcc1
IP: Adding default gateway over PPP over Ethernet vcc1
IP: Initialization complete
IPSec: initializing service
IPSec: No feature key available - service disabled
PPP: PPP over Ethernet vcc1 binding to PPPoE
PPP: PPP over Ethernet vcc1 Port listening for incoming PPP connection requests
RFC1483-1 up
Service-Name=ANY
Host-Uniq 00000001
AC-Name=62011050058192-SMS1800
Service-Name=ANY
lcp: LCP Send Config-Request+
MAGIC 0x2dee0000+
lcp: LCP Recv Config-Req:+
MRU(1492) (ACK) AUTHTYPE(c223) (CHAP) (ACK) MAGICNUMBER
(4403604) (ACK)
lcp: returning Configure-Ack
chap: received challenge, id 1
chap: received success, id 1
ipcp: IPCP Config-Request+
ADDR(0x0) DNS(0x0) DNS2(0x0) WINS(0x0) WINS2(0x0)
ipcp: IPCP Recv Config-Req:+
ADDR(143.137.199.254) (ACK)
ipcp: returning Configure-ACK
ipcp: IPCP Config-Request+
ADDR(0x0) DNS(0x0) DNS2(0x0)
ipcp: IPCP Config-Request+
ADDR(0x8f89c702) DNS(0x8f89320a) DNS2(0x8f898909)
ipcp: negotiated remote IP address 143.137.199.254
ipcp: negotiated IP address 143.137.199.2
ipcp: negotiated TCP hdr compression off
NTP: Update system date & time
TS: "admin" logging in on serial port 0
TS: "Admin" completed login: Full Read/Write access
TS: "Admin" completed login: Full Read/Write access