Netopia and the Netopia logo are registered trademarks belonging to Netopia, Inc., registered U.S. Patent and Trademark Office. Broadband Without Boundaries and 3-D Reach are trademarks belonging to Netopia, Inc. All other trademarks are the property of their respective owners. All rights reserved.
Netopia 3D Reach Utility Installation For Microsoft Windows 98SE, ME, 2000 1. Insert the CD. The Setup utility will run automatically and load the driver for the Netopia 3D Reach Wireless PC Card. When the installation is complete, a new Wireless communication icon will appear in your system tray in the Windows toolbar.
Windows taskbar as shown in figure 2-2. You can double click it to display the main menu, if you chose to close the Netopia 3D REACH Utility menu ear- lier. You can also right-click on it and select the option Exit to exit the Netopia 3D REACH...
Page 7
Note:] When the Netopia 3D REACH Utility exits from the system, it will restore WZC to its initial state before starting Netopia 3D REACH Utility, for example, if WZC is stopped before the Netopia 3D REACH Utility started. WZC will stay stopped after the Netopia 3D REACH Utility terminated.
Site Survey Under the Site Survey tab, the system displays the information of surrounding Access Points from the results of the last scan. List information includes SSID, BSSID, Signal, Channel, Encryption Algorithm, and Network Type as shown in Figure 3-1. Figure 3-1 Detail information of site survey page Definition of each field 1.
Page 9
7. Network Type: Network type in use, Infrastructure for BSS, Ad-Hoc for IBSS network. Connected network: 1. When the Netopia 3D REACH Utility is running, it will automatically select the best Access Point to which to connect. 2. If you want to connect to another Access Point, you can double click on the desired Access Point to make the connection.
ADD/EDIT Profile 1. System Configuration as shown in figure 3-2. Profile Name: You can enter a name for this profile. SSID: You can input the intended SSID name or use the pull down menu to select from the available Access Points. Power Save Mode: You can choose CAM (Constantly Awake Mode) or Power Saving Mode.
Page 11
ADD/EDIT Profile RTS Threshold: You can adjust the RTS threshold number by sliding the bar or key directly to a value. The default value is 2347. Fragment Threshold: You can adjust the Fragment threshold number by sliding the bar or key directly to a value. The default value is 2346. Channel: Only available for setting under ad-hoc mode.
Encryption Setting WEP/TKIP/AES Authentication and Security settings, shown in figure 4-1. Authentication Type: Three types of authentication modes are supported by the Neto- pia 3D REACH Utility: Open, Shared, WPA-PSK and WPA system. Encryption Type: For Open and Shared authentication mode, the selections of encryp- tion type are None and WEP.
Page 13
Encryption Setting WEP/TKIP/AES WEP Key: Only valid when using WEP encryption algorithm. The key must match the Access Point's key. There are several formats to enter the keys. 1. Hexadecimal`40bits: 10 Hex characters. 2. Hexadecimal`128bits: 32Hex characters. 3. ASCII`40bits: 5 ASCII characters. 4.
802.1x Setting 802.1x is an authentication protocol for a “WPA” certificate to an authentication server. Shown as figure 14-14 Authentication type: 1. PEAP: Protect Extensible Authentication Protocol. PEAP transport securely authenti- cates data by using tunneling between PEAP clients and an authentication server. PEAP can authenticate wireless LAN clients using only server-side certificates, thus simplify- ing the implementation and administration of a secure wireless LAN.
Page 15
802.1x Setting 3. TTLS: Tunneled Transport Layer Security. This security method provides for certificate- based, mutual authentication of the client and network through an encrypted channel. Unlike EAP-TLS, EAP-TTLS requires only server-side certificates. 4. LEAP: Light Extensible Authentication Protocol. It is an EAP authentication type used pri- marily in Cisco Aironet WLANs.
CA Server Depending on the EAP in use, only the server or both the server and client may be authen- ticated and require a certificate. Server certificates identify a server, usually an authentica- tion or RADIUS server to clients. Most EAPs require a certificate issued by a root authority or a trusted commercial Certificate Authority.
Profile Profile You can save your favorite wireless setting among your home, office, and other public hotspots in a Profile. You can save multiple profiles, and activate the correct one at your preference. Figure 5-1 shows the Profile page setting. Definition of each field: 1.
Page 18
Connection status Indicates connection is successful on current activated profile. Indicates connection failed on current activated profile. Add a new profile. Delete an existing profile. Edit a Profile. Activate selected profile.
Link Status Link Status Figure 6-1 is the Link Status page; it displays detailed information about the current con- nection. Status: Current connection status. If there is no connection, it will show Disconnected. Otherwise, the connected SSID and BSSID will be shown here. Extra Info: Display link status and current channel in use.
Page 20
Signal Strength: Reception signal strength; you can choose to display as a percentage or dBm format. Displays wireless card's TCP/IP and physical address information.
Advanced Advanced Figure 8-1 shows Advanced setting page of the Netopia 3D REACH Utility. Wireless mode: Select wireless mode. “802.11b only” and “802.11 B/G mix” modes are supported. Ad hoc wireless mode: Select Ad hoc wireless mode. “802.11b only”, “802.11 B/G mixed”, and “802.11 G only”...
Page 22
3. Off: Always send frames without protection. TX Rate: Manually force the Transmit using selected rate. Default is auto. Tx Burst: Netopia 3D REACH Utility's proprietary frame burst mode. Fast Roaming at: fast to roaming, setup by transmit power. Turn radio ON/OFF for FAA requirement.
Country Channel List Country Channel List Country channel list, channel classification and range. Classification 0: FCC 1: IC (Canada) 2: ETSI 3: SPAIN 4: FRANCE 5: MKK 6: MKKI (TELEC) 7: ISRAEL Country Name Argentina Australia Austria Bahrain Belarus Belgium Bolivia Brazil Bulgaria...
Page 24
Croatia Cyprus Czech Republic Denmark Ecuador Egypt Estonia Finland France France2 Germany Greece Hong Kong Hungary Iceland India Indonesia Ireland Israel Italy Japan Japan2 Japan3 Jordan Kuwait Latvia Lebanon Latvia Lebanon Liechtenstein Lithuania Country Name Classification Range CH1~13 CH1~13 CH1~13 CH1~13 CH1~13 CH1~13...
Page 25
Country Channel List Country Name Luxembourg Macedonia Malaysia Mexico Morocco Netherlands New Zealand Nigeria Norway Panama Paraguay Peru Philippines Poland Portugal Puerto Rico Romania Russia Saudi Arabia Singapore Slovakia Slovenia South Africa South Korea Spain Sweden Switzerland Taiwan Thailand Turkey United Arab Emirates Classification Range...
Page 26
United Kingdom United States of America Uruguay Venezuela Yugoslavia Country Name Classification Range CH1~13 CH1~11 CH1~13 CH1~13 CH1~11...
About About The About page displays the wireless card and driver version information as shown in fig- ure 9-1. Figure 9-1 About Page It displays the Configuration Utility Version, Driver Version, and EEPROM Version informa- tion.
Page 31
Example: Adding a profile in the site survey page 4. Change the Profile Name to your preference (optional). 5. Click the OK button without changing any other values.
Page 32
6. Follow the examples in the section “Configure connection with WEP ON” on page the section “Configure connection with WPA-PSK” on page 43 or the section “Configure connection with WPA by 802.1x setting” on page 47 to set the authentication and secu- rity page.
Page 35
Example: Adding a profile in the Profile page 3. Change the Profile Name to your preference (optional).
Page 36
4. From the SSID pull-down menu select your desired Access Point. The Access Point list is generated from the results of the site survey.
Page 37
Example: Adding a profile in the Profile page 5. Set the desired Power Saving Mode (optional). 6. Click the Authentication and Security tab.
Page 38
The Authentication and Security page appears. 7. Click the OK button.
Page 39
Example: Adding a profile in the Profile page The created profile appears in the Profile List. 8. Click the Connect button to activate the profile setting.
Page 40
9. Follow the examples in the section “Configure connection with WEP ON” on page the section “Configure connection with WPA-PSK” on page 43 or the section “Configure connection with WPA by 802.1x setting” on page 47 to set the authentication and secu- rity page.
Configure connection with WEP ON Configure connection with WEP ON 1. Select an Access Point with WEP encryption.
Page 42
2. Click the Connect button or double-click on the intended network.
Page 43
Configure connection with WEP ON 3. The Authentication and Security page appears. 4. Enter the proper key setting that matches your Access Point's.
Page 44
5. Click the OK button. An established connection will look like the figure below.
Configure connection with WPA-PSK Configure connection with WPA-PSK 1. Select an Access Point with WPA-PSK authentication mode.
Page 46
2. Click the Connect button or double click the intended network.
Page 47
Configure connection with WPA-PSK The Authentication and Security page appears. 3. The Authentication Type is WPA-PSK.
Page 48
Select the correct encryption (TKIP or AES). Enter the WPA Preshared Key. 4. Click the OK button. ☛ Warning: If the WPA Preshared Key is entered incorrectly, the Access Point will be shown as connected, but you won't be able to exchange any data.
Configure connection with WPA by 802.1x setting Configure connection with WPA by 802.1x setting 1. Select an Access Point with WPA authentication mode.
Page 50
2. Click the Connect button or double-click the desired network.
Page 51
Configure connection with WPA by 802.1x setting 3. The Authentication and Security page appears. 4. Click the 802.1x Setting button.
Page 52
6. Authentication Type and setting method: PEAP: 1. Authentication Type: choose PEAP, enter your identity (example: Netopia) in the Iden- tity field. Tunneled Authentication: Protocol: choose EAP-MSCHAP v2, tunnel Identity is Netopia and tunnel Password is test. The setting is an example.
Page 53
2. Click the OK button. The result will look like the figure below. TLS / Smart Card: 1. Authentication Type: choose TLS / Smart Card, TLS only needs an Identity that is Netopia for server authentication. The setting is an example.
Page 55
Configure connection with WPA by 802.1x setting 2. TLS must use a client certificate. Click the More button to choose a certificate.
Page 56
3. The Certificate Selection page appears. Choose a certificate for server authentica- tion. 4. To display certificate information in use see the client Certification page.
Page 57
Configure connection with WPA by 802.1x setting 5. Click the OK button. The result will look like the figure below.
Page 59
Configure connection with WPA by 802.1x setting TTLS: 1. Authentication Type: choose TTLS; Identity is Netopia. For Tunnel Authentication Pro- tocol choose CHAP, tunnel Identity is Netopia and tunnel Password is test. The setting is an example. 2. Click the OK button.
Page 60
The result will look like the figure below.
Page 61
Configure connection with WPA by 802.1x setting MD5: 1. Authentication Type: choose MD5; MD5 only needs identity and password - Netopia and test - for server authentication. The setting is an example. 2. Click the OK button.
Page 62
The result will look like the figure below.
Configure connection with WPA by 802.1x setting Excursuses The above setting is a test platform by Netopia, inc. You can set the functions in accor- dance with the Access Point. Acknowledgements: “This product includes software developed by MDC and its licensors. This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http:// www.openssl.org/)”.