Camshaft Removal - DAELIM ROADWIN VJ125 Service Manual

AC GENERATOR CAP AC GENERATOR CAP AC GENERATOR CAP AC GENERATOR CAP AC GENERATOR CAP
AC GENERATOR CAP AC GENERATOR CAP AC GENERATOR CAP AC GENERATOR CAP
AC GENERATOR CAP AC GENERATOR CAP
AC GENERATOR CAP AC GENERATOR CAP AC GENERATOR CAP AC GENERATOR CAP AC GENERATOR CAP
SEALING SCREW SEALING SCREW SEALING SCREW
SEALING SCREW SEALING SCREW SEALING SCREW SEALING SCREW
SEALING SCREW SEALING SCREW SEALING SCREW SEALING SCREW
SEALING SCREW SEALING SCREW SEALING SCREW SEALING SCREW
SEALING SCREW SEALING SCREW SEALING SCREW
TENSIONER MOUNTING BOLTS TENSIONER MOUNTING BOLTS TENSIONER MOUNTING BOLTS
TENSIONER MOUNTING BOLTS TENSIONER MOUNTING BOLTS TENSIONER MOUNTING BOLTS TENSIONER MOUNTING BOLTS
TENSIONER MOUNTING BOLTS TENSIONER MOUNTING BOLTS TENSIONER MOUNTING BOLTS TENSIONER MOUNTING BOLTS
TENSIONER MOUNTING BOLTS TENSIONER MOUNTING BOLTS TENSIONER MOUNTING BOLTS TENSIONER MOUNTING BOLTS TENSIONER MOUNTING BOLTS
CAMSHAFT HOLDER NUTS CAMSHAFT HOLDER NUTS CAMSHAFT HOLDER NUTS
CAMSHAFT HOLDER NUTS CAMSHAFT HOLDER NUTS CAMSHAFT HOLDER NUTS CAMSHAFT HOLDER NUTS
CAMSHAFT HOLDER NUTS CAMSHAFT HOLDER NUTS CAMSHAFT HOLDER NUTS CAMSHAFT HOLDER NUTS
CAMSHAFT HOLDER NUTS CAMSHAFT HOLDER NUTS CAMSHAFT HOLDER NUTS CAMSHAFT HOLDER NUTS CAMSHAFT HOLDER NUTS
BOLTS BOLTS BOLTS
BOLTS BOLTS
BOLTS BOLTS BOLTS BOLTS BOLTS BOLTS
BOLTS BOLTS BOLTS BOLTS
BOLTS
CAP CAP CAP
CAP CAP
CAP CAP CAP CAP CAP CAP
CAP CAP CAP CAP
CAP
CRANK SHAFT HOLE CAP CRANK SHAFT HOLE CAP CRANK SHAFT HOLE CAP CRANK SHAFT HOLE CAP CRANK SHAFT HOLE CAP
CRANK SHAFT HOLE CAP CRANK SHAFT HOLE CAP CRANK SHAFT HOLE CAP CRANK SHAFT HOLE CAP CRANK SHAFT HOLE CAP CRANK SHAFT HOLE CAP
CRANK SHAFT HOLE CAP CRANK SHAFT HOLE CAP
CRANK SHAFT HOLE CAP CRANK SHAFT HOLE CAP CRANK SHAFT HOLE CAP CRANK SHAFT HOLE CAP CRANK SHAFT HOLE CAP
CYLINDER HEAD / VALVES
CAMSHAFT
REMOVAL
Remove the noise suppressor cap assembly from
the spark plug.
Remove the cylinder head cover bolts and cover.
The camshaft can be maintained without
removing the engine.
Remove the AC generator cap and crank shaft hole
cap out of the left crankcase cover.
Turn the crankshaft to the left, and align the T mark
of the flywheel with the index mark of the LH.
crankcase cover.
Verify that the piston is located at the top dead center.
(Make all camshaft lobes face downward.)
If all camshaft lobes face upward, rotate the crankshaft
to the left for 1 turn (360 ), and align the T
with the index mark once again.
Disconnect the starter motor cable from the starter
motor.
Remove the clutch wire holder.
Remove the starter motor mounting bolts and
starter motor.
Remove the O-ring and pan screw from the cam
chain tensioner lifter. Remove the tensioner
mounting bolt and tensioner lifter.
Remove the camshaft holder 8mm nuts and remove
the camshaft holder from the cylinder.
mark
9-3