Program Bank X1; Stereo (0.0-4.9) - Lexicon PCM 80 - REV 1 DUAL FX User Manual

PCM 80 Dual FX User Guide

Program Bank X1

Stereo
(X1 0.0 – X0 4.9)
3-6
4.5 SlipTheEkos1
Similar to SlipTheBeat1, but feedback has been turned up a bit to create a series of
rhythmic repeats. The delays are set for a 3 against 2 pattern that alternates between left
and right, then routed through a stereo drum chamber. The reverb mix is set to be
completely dry. Rvb Mix and other useful controls await you in the Soft Row.
4.6 SlipTheEkos2
A variation of SlipTheEkos1 with more dramatic delay settings. Also the reverb is in
parallel in this program to provide some extra punch on the initial attack. T
4.7 SlipTheEkos3
The delays are set to produce a rolling triplet pattern that cycles from side to side in this
variation of SlipTheEkos1. The reverb is in parallel in this program to provide some extra
punch on the initial attack. T
4.8 SlipTheBeat1
In this mono-in/stereo out program, the left and right inputs are combined — then sent into
a slap delay and, from there, sent through a stereo chamber. ADJUST is used to vary the
slap from no delay to a full beat. Use this program to slide a snare (or other rhythm
instrument) behind the beat. You can mix this delayed signal with the original source to
fatten it up, or use it without the original if you want to change the groove by having the
snare lay back. T
4.9 SlipTheBeat2
A variation of SlipTheBeat1. In this program the drum chamber is put in front of the slap
to fatten up the sound. T
0.0 KnobLocation
This preset provides a quick way to steer a stereo source between the center, side and
rear channels of an LCRS mix. No processing other than steering is applied to the source
material. ADJUST determines the LCRS placement of stereo source material as follows:
0=center only, 45=left and right, 90=surround. Soft Row parameters have been set up to
allow you to quickly add various amounts of chorus, delays and reverb. This preset is not
mono compatible.
0.1 KnobPanSwap
Use the knob to swap the left/right panning of a stereo source. No processing other than
steering is applied to the source material. ADJUST determines the width of stereo source
material as follows: 0 = left / right swap, 45 = mono, 90 = normal stereo. Soft Row
parameters have been set up to allow you to quickly add various amounts of chorus,
delays and reverb.
0.2 AutoPanSwap
A variation of KnobPanSwap. In this version the LFO controls the stereo width. ADJUST
controls the speed of the panning. Chorus and echoes can be added.
0.3 ips PlateSlap
The ips TapeSlap program is used as a predelay for a plate reverb. ADJUST sets the tape
speed. 1 = 30 ips, 2 = 15 ips, 3 = 7.5 ips, 4 = 3.75 ips. Reverb controls are in the Soft Row.
0.4 15ips Plate
Plate reverb with a stereo 15 ips predelay. The predelay has a slight amount of feedback.
ADJUST controls the predelay / reverb mix.
ADJUST: Back Beat
ADJUST: Back Beat
ADJUST: Back Beat
ADJUST: Back Beat
ADJUST: Back Beat
ADJUST: Width
ADJUST: Width
ADJUST: Pan Speed
ADJUST: TapeSpeed
ADJUST: Rvb Mix
Lexicon
0–100
0–100
0–100
0–100
0–100
0–90
0–90
0–90
1–4
0–100