Optimizing The Speaker Setting For Your; When An Error Message Is Displayed During Measurement; Measurement - Yamaha RX-V765 Owner's Manual

Optimizing the speaker setting for your listening room (YPAOj
5
To select a sound character for adjustment,
press [j]Cursor
V
to select "EO Type" and
then press [j]Cursor <l
1
C>.
If
this unit does not work when you press [j]Cursor,
press ImISETUP once and then operate this unit.
This unit has a parametric equalizer that adjusts the
output levels for each frequency range. The equalizer
is adjusted to produce a cohesive sound field based on
automatically measured speaker characteristics.
In "EQ Type," you can select the following
parametric equalizer characteristics suitable for the
desired sound characteristics.
t·j.:l"t.ur·.'.jl
Adjusts all speakers to achieve natural sound. Select
this if sounds in the high frequency range seem too
strong when "EQ Type" is set to "Flat."
Fl.::I+"
Adjusts each speaker to obtain the same
characteristics. Select this if your speakers have
similar qualities.
Fr'on+"
Adjusts each speaker to obtain the same
characteristics as the front left and right speakers.
Select this if your front left and right speakers have
significantly better qualities than the other speakers.
6
Press [j]Cursor
V
to select "Start" and then
press [j]ENTER to start the setup procedure.
A countdown starts and a measurement starts in 10
seconds. A loud test tone is output during
measurement.
Notes
• During the automatic setup procedure, do not perform any
operation on this unit.
• To cancel the automatic setup procedure. press
!TIJCursor
t,.
Measurement takes about 3 minutes. To obtain
precise results, stay where you will not disturb the
measurement, such as to the side of or behind the
speakers or outside the room.
When measurement is successfully completed,
"YPAO Complete" appears on the front panel display
and the results appear on the video monitor.
DIST
Displays the speaker distance from the listening position
in the following order:
Closest speaker distancelFarthest speaker distance
L.I.)L.
Displays the speaker output levels in the following order:
Lowest speaker output level/Highest speaker output level
Notes
• If "ERROR" appears on the video monitor during the automatic setup
procedure. measurement is canceled and the type of error is displayed.
For details, see "When an error message is displayed during
measurement" (see page 23).
• If problems occur during measurement, "WARNING (XX)" (xx indicates
the number of warning) appears above "RESULT" (see page 23).
7
Press [j]ENTER.
The speaker characteristics are adjusted according to
measurement results.
To cancel the operation, press [j]Cursor <ll
C>
to
select "Cancel" and press [j]ENTER.
When the following screen appears, remove the
optimizer microphone. The automatic setup
procedure is now complete.
RUTO SETUP
Co~plete
[) i
:=·conn€'c+..
t' 1 i
(.r·oP~-ll)ne
PRESS [EtHER]
[SETUP]: E:,(
i
t
The optimjzer microphone is sensitive to heat. Store it
in a cool place and away from direct sunlight after
measurement. Do not leave it in a place where it will be
subjected to high temperatures such on an AV
component.
,0,
~'i>~
• If you do not want to apply the measurement results, select "Cancel."
• Perform the automatic setup procedure again if you change the number
or positions of speakers.
• If you press
!TIJENTER
before removing the optimizer microphone.
'" Auto Setup" of "Speaker Setup" in the SETUP menu (see page 54) is
displayed.
RESULT
r.iST;
LUL :
., >5e+..
[-ol]/[ ..
]:Selec.t
[EtHER]:
Finish
SF'
Displays the number of speakers connected to this unit in
the following order:
Total of Front, Center, and Presencerrotal of Surround and
Surround BackJSubwoofer
22
En