Denon AVR-4810CI Owner's Manual page 45

Making Detailed Settings (Manual Setup)
Setting items
Speaker Configuration Front Height : Set the presence and size of the front height speakers.
(Continued) • Large : Use of a large speaker that can adequately playback low
frequencies.
• Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
• None : Select when the front height speakers are not connected.
When "Configuration" is set to "5.1ch" in the "Amp Assign" settings
(vpage 41) or when "FH" is not selected using "Extra Channel", no
settings can be made for "Front Height".
Front Wide : Set the presence and size of the front wide speakers.
• Large : Use of a large speaker that can adequately playback low
frequencies.
• Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
• None : Select when the front wide speakers are not connected.
When "Configuration" is set to "5.1ch" in the "Amp Assign" settings
(vpage 41) or when "FW" is not selected using "Extra Channel", no
settings can be made for "Front Wide".
Bass Setting Subwoofer Mode : Select low range signals to be reproduced by
Settings for subwoofer and subwoofer.
LFE signal range playback. • LFE : The low range signal of the channel set to "Small" speaker size is
added to the LFE signal output from the subwoofer.
• LFE+Main : The low range signal of all channels is added to the LFE
signal output from the subwoofer.
• This can be set when "Speaker Configuration" – "Subwoofer" (vpage
41) is set to "Yes".
• Play music or a movie source and select the mode offering the strongest
bass.
• Select "LFE+Main" if you want the bass signals to always be produced
from the subwoofer.
LPF for LFE : Set LFE signal playback range.
• 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz

Main remote control unit
operation buttons
Setting contents
:Displaying the menu
Cancel the menu
Setting items
Distance Feet / Meters : Set the unit of distance.
Set distance from listening
Step : Set the minimum variable width of the distance.
position to speakers. • 1ft / 0.1ft
Measure beforehand the
• 0.1m / 0.01m
distance from the listening
Default : Reset all distance settings to factory default.
position to each speaker. • Yes : Reset to the defaults.
• No : Do not reset to the defaults.
When you select "Default" and press
to the default?" prompt is displayed. Select either "Yes" or "No", and
press
Front L / Front R / Center / Subwoofer / Surround A L / Surround A R
/ Surround B L / Surround B R / Surr. Back L z / Surr. Back R z / Front
Height L / Front Height R / Front Wide L / Front Wide R : Select the
speaker.
z: When the "Speaker Configuration" – "Surround Back" setting
(vpage 41) is set to "1spkr", "Surr. Back" is displayed.
• 0.0ft ~ 60.0ft / 0.00m ~ 18.00m : Set the distance.
• Speakers set to "None" in "Speaker Configuration" (vpage 41) are
not displayed.
• The speakers that can be selected differ depending on the "Amp Assign"
(vpage 41) and "Speaker Configuration" (vpage 41) settings.
• Default settings :
Front / Center / Subwoofer / Front Height / Front Wide : 12.0 ft (3.60 m)
Surround A / Surround B / Surround Back : 10.0 ft (3.00 m)
• Set the difference in the distance between the speakers to less than 20
feet (6.0 meters).
Channel Level Test Tone : Output test tone.
Set the volume of the test • Front L / Front Height L / Center / Front Height R / Front R / Front
Wide R / Surround R /Surr. Back R z /Surr. Back L z / Surround L /
tone to be the same when it
Front Wide L / Subwoofer : Select the speaker.
is output from each speaker.
z : When the "Speaker Configuration" – "Surround Back" setting
(vpage 41) is set to "1spkr", "Surr. Back" is displayed.
• –12dB ~ +12dB (0dB) : Adjust the volume.
• Speakers set to "None" in the "Speaker Configuration" (vpage 41)
settings are not displayed.
• When
"Subwoofer" setting switches to "OFF".
• When a headphones jack is inserted in the PHONES terminal of the AVR-
4810CI, the "Channel Level" is not displayed.
• You can also press
Volume of the Different Speakers").
:Moves the cursor
:Confirm the setting
(Up/Down/Left/Right)
Setting contents
ENTER
, the "Return all settings
ENTER
.
o is pressed while the subwoofer volume is set to "–12 dB", the
CHANNEL LEVEL
to set (vpage 100 "Adjust the
:Return to previous menu