Denon AVR-4810CI Owner's Manual page 37

Make the Optimal Speaker Settings, and Correct the Room Acoustics (Audyssey™ Auto Setup)
s Audyssey Auto Setup Preparations
around items indicate the settings.
STEP1 Preparation
Perform the following settings if adjustments, etc., are required for
the speaker environment you're using.
If you do not need to perform the following settings, or have already
completed them, select "Auto Setup Start" and then press
Proceed to " STEP2 ".
Change the Amplifier Assignment (Amp Assign)
It is possible to switch the signals being output from the Bi-Wir. or Bi-
Amp, FRONT, S.BACK/F.HEIGHT/F.WIDE, F.HEIGHT/F.WIDE, ZONE2
and ZONE3 speaker terminals on the AVR-4810CI to suit the speaker
environment being used (vpage 39 ~ 41 "Amp Assign").
1
Select "Amp Assign"
and then press
ENTER
.
2
Pressing o p , select the MAIN ZONE channel
configuration ("Configuration") and then press
5.1ch
7.1ch 9.1ch
3
When selecting "7.1ch" or "9.1ch" in step 2, press
p to select the channels to be used ("Extra Channel"),
and then press .
i
When setting "Configuration" to "7.1ch"
n
: When using surround back channel
SB
: When using front height channel
FH
: When using front wide channel
FW
When setting "Configuration" to "9.1ch"
n
: When using surround back channel and front height
SB/FH
channel
: When using surround back channel and front wide
SB/FW
channel
: When using front height channel and front wide
FH/FW
channel

Main remote control unit
operation buttons
4
Pressing o p
amp ("Assign Mode"), and then press
: This is the usual configuration.
NORMAL
: Assign a power amp to ZONE2 audio.
+Z2
: Assign a power amp to ZONE2 and ZONE3 audio.
+Z2+Z3
: Assign all power amps to ZONE2 audio.
ALL Z2
ENTER
.
: Assign all power amps to ZONE2 and ZONE3 audio.
ALL Z2+Z3
: Freely assign power amps to the desired channels.
FREE
5
Pressing o p
front speakers ("Front"), and then press
: This is the usual configuration.
NORMAL
Bi-WIRING : Bi-wire the front speakers.
: Bi-amp the front speakers.
Bi-AMP
: Bi-wire another front speaker for 2 channel play
2CH BW
mode.
: Bi-amp another front speaker for 2 channel play
2CH BA
mode.
6
The following screen is displayed.
The speaker terminals and the output from the pre-out terminals
can be checked on this screen.
.
i
11.1ch
o
q
w
See page 14, 15 on how to connect the speakers.
b
:Displaying the menu
Cancel the menu
, set the usage method for the power
.
i
, set the connection method for the
.
i
q C urrent settings
w S peaker terminal name
e Signal being output from
speaker terminal
r O utput from pre-out
terminal
b Terminals not being used
are greyed out.
e
r
:Moves the cursor
:Confirm the setting
(Up/Down/Left/Right)
• When you are using speaker terminals for multi-zone (ZONE2/
ZONE3), set "Assign Mode" to "+Z2" or "+Z2+Z3".
• You can set in the same way as described in "Amp Assign" on page
34.
NOTE
Since "Configuration" of AVR-4810CI is set to "5.1ch" by default,
audio is not output from the surround back speakers. When using
the surround back speakers with MAIN ZONE, set "Configuration"
to something other than "5.1ch", and then select "SB" in "Extra
Channel".
Set the Channels You will not Use (Channel Skip)
If you set the channels you will not use beforehand, those channels
will not be measured. Therefore, you can save an amount of time
commensurate with that which would have been taken to measure
those channels.
1
Select "Channel
Skip" and then press
ENTER .
2
Press to select a channel, press
ui
ENTER
the item, and then press .
n Configurable channels
Subwoofer : Set the subwoofer channel.
Surround Back : Set the surround back channel.
: Set the front height channel.
Front Height
Front Wide : Set the front wide channel.
Settings
n
Measure : Measure the selected channel.
Skip : Skip the selected channel and do not measure.
RETURN
To cancel, press .
b
Displayed when "Surround Back", "Front Height" and "Front Wide"
are set using "Extra Channel" in "Amp Assign".
:Return to previous menu
to select
o p