Omron EJ1 User Manual page 271

Parameter List
Vari- CompoWay/F Modbus
able
Category Add- Address
type
ress
DA Can be 0100 F000
(9A) changed
0101 F001
during
V1.1
opera-
0102 F002
tion.
0103 F003
0104 F004
0105 F005
0106 F006
0107 F007
0108 F008
0109 F009
0140 F040
0141 F041
0142
F042
0143 F043
0144 F044
0145 F045
0146 F046
0154
F054
0180 F080
0181 F081
0184 F084
0185
F085
0186
F086
0187 F087
0188 F088
0189 F089
018A F08A
018B F08B
018C F08C
018D
F08D
018E F08E
018F
F08F
0190 F090
0191 F091
0192 F092
0193 F093
0194
F094
0195
F095
Not used.
0200 F100
0300 F200
0400 F300
246
Parameter name
G3PW1-Internal Duty Setting
G3PW1-Base-up Value
G3PW1-Soft-start Up Time
G3PW1-Soft-start Down Time
G3PW1-Output Upper Limit
G3PW1-Output Lower Limit
G3PW1-Heater Burnout Threshold
G3PW1-Heater Characteristic Resistance for
Phase Control
G3PW1-Heater Characteristic Resistance for
Optimum Cycle Control
G3PW1-Heater Burnout Detection Lower
Limit
G3PW1-Input Monitor
G3PW1-Duty Monitor
G3PW1-Output Monitor
G3PW1-Phase Angle Monitor
G3PW1-Current Monitor
G3PW1-Total Run Time Monitor
G3PW1-Status
Version
G3PW1-Send Wait Time
G3PW1-Communications Timeout Time
G3PW1-Communications Main Setting Num-
ber
G3PW1-External Duty Input Enable/Disable
G3PW1-Output Mode Selection
G3PW1-Input Digital Filter Time Constant
G3PW1-Input Signal Type
G3PW1-Main Setting Automatic Input Selec-
tion
G3PW1-Main Setting Manual Input Selection
G3PW1-Control Method Default
G3PW1-Main Setting Automatic/Manual
Default
G3PW1-Number of Alarms for Heater Burnout
Detection
G3PW1-Load Current Upper Limit
G3PW1-Event Input Assignment
G3PW1-Alarm Output Open in Alarm
G3PW1-Heater Burnout Alarm Operation
G3PW1-Total Run Time Exceeded Alarm
Operation
G3PW1-Total Run Time Alarm Set Value
G3PW1-External Input Range Alarm Opera-
tion
G3PW1-External Duty Input Alarm Operation
G3PW2 - Internal Duty Setting
G3PW3 - Internal Duty Setting
G3PW4 - Internal Duty Setting
Setting (monitor) range
H' 00000000 to H' 000003E8 (0.0 to 100.0)
H' 00000000 to H' 000003E8 (0.0 to 100.0)
H' 00000000 to H' 000003E7 (0.0 to 99.9)
H' 00000000 to H' 000003E7 (0.0 to 99.9)
H' 00000001 to H' 000003E8 (0.1 to 100.0)
H' 00000000 to H' 000003E7 (0.0 to 99.9)
H' 00000000 to H' 00000064 (1 100)
H' 00000000 to H' 00000064 (1 to 100)
H' 00000000 to H' 000003E7 (0.0 to 99.9)
H' 00000000 to H' 000003E8 (0.0 to 100.0)
H' 00000000 to H' 000003E8 (0.0 to 100.0)
H' 00000000 to H' 000003E8 (0.0 to 100.0)
H' 00000000 to H' 000003E8 (0.0 to 100.0)
H' 00000000 H' 000003E8 (0.0 to 100.0)
H' 00000000 to H' 000002EE (0.0 to 75.0)
H' 00000000 to H' 000003E7 (0.0 to 99.9)
---
---
H' 00000000 to H' 00000063 (0 to 99)
H' 00000000 to H' 000003E7 (0 to 999)
H'00000000: Automatic Assignment (0)
H'00000001: EJ1 CH1 Control output (heating) (1)
H'00000002: EJ1 CH2 Control output (heating) (2)
H'00000003: EJ1 CH3 Control output (heating) (3)
H'00000004: EJ1 CH4 Control output (heating) (4)
H'00000005: EJ1 CH1 Control output (cooling) (5)
H'00000006: EJ1 CH2 Control output (cooling) (6)
H'00000007: EJ1 CH3 Control output (cooling) (7)
H'00000008: EJ1 CH4 Control output (cooling) (8)
H' 00000000: Disabled (0)
H' 00000001: Enabled (1)
H' 00000000: Proportional to Phase Angle
(for G3PX Compatibility) (0)
H' 00000001: Proportional to Square Voltage (1)
H' 00000002: Proportional to Voltage (2)
H' 00000003: Constant Current (3)
H' 00000000 to H' 000003E8 (0.0 to 100.0)
H' 00000000: Linear Input (0)
H' 00000001: Voltage ON/OFF Input (1)
H' 00000000: 4 to 20 mA or 1 to 5 V (0)
H' 00000001: Communications (1)
H' 00000000: External Adjuster Input (0)
H' 00000001: Key Input (1)
H' 00000000: Phase Control (0)
H' 00000001: Optimum cycle control (1)
H' 00000000: Automatic (0)
H' 00000001: Manual (1)
H' 00000000 to H' 000003E7 (0 to 999)
H' 00000000 to H' 00000294 (0.0 to 66.0)
H' 00000000: No Assignment (0)
H' 00000001: Control Method Selection (1)
H' 00000002: Main Setting Automatic/Manual
Selection (2)
H' 00000000: Close in alarm (0)
H' 00000001: Open in alarm (1)
H' 00000000: Disable (0)
H' 00000001: Alarm Level 1 (1)
H' 00000002: Alarm Level 2 (2)
H' 00000000: Disable (0)
H' 00000001: Alarm Level 1 (1)
H' 00000002: Alarm Level 2 (2)
H' 00000000 to H' 000003E7 (0 to 99.9)
H' 00000000: Disable (0)
H' 00000001: Alarm Level 1 (1)
H' 00000002: Alarm Level 2 (2)
H' 00000000: Disable (0)
H' 00000001: Alarm Level 1 (1)
H' 00000002: Alarm Level 2 (2)
The rest are the same as the G3PW1.
Appendix
De- Unit Attrib- Target Unit
fault utes
TC4/ HFU
TC2
●
0.0 % NUM ---
●
0.0 % NUM ---
●
0.5 s NUM ---
●
0.0 s NUM ---
●
100.0 % NUM ---
●
0.0 % NUM ---
●
100 % NUM ---
●
100 % NUM ---
●
0.0 W NUM ---
●
0.0 % NUM ---
●
0.0 % NUM ---
●
0.0 % NUM ---
●
NUM ---
0.0 %
●
0.0 % NUM ---
●
0.0 A NUM ---
●
0.0 kh NUM ---
●
--- --- NUM ---
●
NUM ---
--- ---
●
1 ms NUM ---
●
0 s NUM ---
●
0 --- NUM ---
●
NUM ---
0 ---
●
NUM ---
0 ---
●
0.0 ms NUM ---
●
0 --- NUM ---
●
0 --- NUM ---
●
0 --- NUM ---
●
0 --- NUM ---
●
0 --- NUM ---
●
NUM ---
150 Times
●
0.0 A NUM ---
●
NUM ---
0 ---
●
1 --- NUM ---
●
0 --- NUM ---
●
0 --- NUM ---
●
0.0 kh NUM ---
●
NUM ---
1 ---
●
NUM ---
1 ---