Omron EJ1 User Manual page 132

Other Functions (TC4 and TC2)
■ Bus Input Assignments (TC4/TC2)
Bus input 1
Bus inputs 2 and 3 can be set in the same way.
Settable Channels 3 and 4 are supported only by the TC4.
parameters
All channels
Disabled
Bank (bit 0)
Bank (bit 1)
Stop (0)/Run (1)
Run (0)/Stop (1)
Auto (0)/Manual (1)
Local SP (0)/Remote SP (1)
■ Bus Output Assignments (TC4/C2)
Bus input 1
Bus inputs 2 and 3 can be set in the same way.
Settable
Channels 3 and 4 are supported only by the TC4.
parameters
All channels
Disabled
Temperature Controller Error
All Alarm OR
All Alarm AND
Alarm 1 to 3 OR
Alarm 1 to 3 AND
Input Error OR
RSP Input Error OR
HB (Heater Burnout) Alarm OR
HS (Heater Short) Alarm OR
OC (Heater Overcurrent) Alarm OR
Event Input 1 to 4
Bus Input 1 to 3
Note Temperature Controller Error
The Temperature Controller Error output will turn ON when an bit
between bit 0 and bit 13 in the Device A Status is ON. It can be
used to output EJ1 error status. Refer to Status Lists on page 255
for details on Device A Status.
Variable type
F2/B2
Conditions for use
Bus input 2 Bus input 3
Channel 3
Bank (bit 0)
Channel 2
Bank (bit 1)
Bank (bit 0)
Channel 1
Stop (0)/Run (1)
Bank (bit 1)
Bank (bit 0)
Run (0)/Stop (1)
Stop (0)/Run (1)
Bank (bit 1)
Auto (0)/Manual (1)
Run (0)/Stop (1)
Stop (0)/Run (1)
Local SP (0)/Remote SP (1)
Auto (0)/Manual (1)
Run (0)/Stop (1)
Local SP (0)/Remote SP (1)
Auto (0)/Manual (1)
Local SP (0)/Remote SP (1)
Bus input 2 Bus input 3
Channel 3
Alarm 1 to 3
Channel 2
All Alarm OR
Alarm 1 to 3
Channel 1
All Alarm AND
All Alarm OR
Alarm 1 to 3
Input Error
All Alarm AND
All Alarm OR
RSP Input Error
Input Error
All Alarm AND
Heater Burnout Alarm
RSP Input Error
Input Error
HS Alarm
Heater Burnout Alarm
RSP Input Error
OC Alarm
HS Alarm
HB (Heater Burnout) Alarm
Bank (bit 0)
OC Alarm
HS (Heater Short) Alarm
Bank (bit 1)
Bank (bit 0)
OC (Heater Overcurrent) Alarm
Stop (0)/Run (1)
Bank (bit 1)
Bank (bit 0)
Run (0)/Stop (1)
Stop (0)/Run (1)
Bank (bit 1)
Auto (0)/Manual (1)
Run (0)/Stop (1)
Stop (0)/Run (1)
Local SP (0)/Remote SP (1)
Auto (0)/Manual (1)
Run (0)/Stop (1)
Local SP (0)/Remote SP (1)
Auto (0)/Manual (1)
Local SP (0)/Remote SP (1)
Parameter name
Bus Input 1 to 3 Assignment
(Common)
Bus Output 1 to 3 Assignment
(Common)
No special conditions
Section 4-7
Channel 4
Bank (bit 0)
Bank (bit 1)
Stop (0)/Run (1)
Run (0)/Stop (1)
Auto (0)/Manual (1)
Local SP (0)/Remote SP (1)
Channel 4
Alarm 1 to 3
All Alarm OR
All Alarm AND
Input Error
RSP Input Error
Heater Burnout Alarm
HS Alarm
OC Alarm
Bank (bit 0)
Bank (bit 1)
Stop (0)/Run (1)
Run (0)/Stop (1)
Auto (0)/Manual (1)
Local SP (0)/Remote SP (1)
Setting range Default
TC4: 0 to 132 0
TC2: 0 to 69
TC4: 0 to 150 0
TC2: 0 to 87
107