Table of Contents
Advertisement
InfZnite
816
Key Telephone
System
SYSTEM PARAMETERS
PROGRAMMING
-
The asterisk
['I is used to indicate
a
Pulse-To-Tone
switchover.
-
The Pound
[#I button
to insert a
Pause command.
-
The ELASH button
to program
a
Flash command.
-
The CONF button
is used to program
a "No Display".
The [*I can be programmed
as a digit.
e. Press HOLD button.
To continue
programming
additf onal numbers,
repeat from step a.
730.19
SETTING
SYSTEM
DATE AND
System date and time can be set only from the
attendant
statfon
and must
be done
in the
following
manner:
a,. Press
AUTO/SAVE
button
twice.
b. Dial [501 on the d&l pad.
c. Enter date and time as follows:
YYMMDDHHMM
-
YY=year80to
99
-
MM=monthOl
to 12
-
DD=dayOlto31
-
HH = hour 00 to 23
-
MM=minuteOOto59
d. Press HOLD to enter.
730.20
PHONE BOX PROGRAMMING
The following
program
parameters
should
be
considered
where Phone
Box operation
is de-
sired.
1. Program
Station
Class of Service to COS 6
for the desired phone box staff on. Refer to
Section
710.1.
Station
Class of Service.
2. Assign Alarm/Phone
Box signabng
to sta-
tions to receive phone box signahng.
Refer
to Section
710.2,
Station
Configuration.
3. Program
the type of Alarm/Phone
Box sig-
naling
is desired:
The options
are:
-
A continuously
repeated
warble tone of
.25s on/.25s
off.
-
A
Single burst
of tone ring (once)
Refer to Section
730.1,
System ConfQuraUon
730.21
SINGLE LILW STATION
ADAPTER
(SLA) PROGRAMhIING
The SLA stations
are programmed
in the same
manner
a key telephone
is programmed
in the
system
data base admin.
Attributes
such as
StaUon
COS. feature
access. CO Line Rtnging.
Pick Up group, etc... can be assigned
to a single
line station
connected
to the SLA adapter.
Refer
to Table
730.1
for a complete
list of
Program
Codes that can affect SLA operatfon.
Refer to the systems manual
for complete
pro-
gramxning
procedures
and station
attributes
that can appiy to SLA station
ports.
lkble 730-l
Applicable
SLA Program
Codes
r
I
PROGRAM
CODE
Class
of Service
Do Not Disturb
System Speed Dial
Alarm/Door
Signal
Preferred
Line Answer
(must be enabled)
Call Forwarding
Pick Up Group
CO Line Ringing,
Day
CO Line Ringing.
Night
Message Reminder
Tone
Preset Forward
Sta Assign
DF=Data
Field
SF=Sub-Field
816
DFOl
DF 02, SF 1
DF 02. SF 2
DF 02, SF 3
DF 02, SF 4
DF 02, SF 5
DF 05
DF 13
DF 14
DF 25
DF 33
1
The following
are some of the parameters
that
require special attentfon
for stations
connected
toaSIA.
A
Preferred
Line Answer
(PLAI
For proper
operation
of a single line telephone
or device connected
to a SIA.
Preferred
Line
Answer
(PLA) mJlst be enabled
in Data
base
adrnhr
for each SLA port that
is connected.
This is performed
in program
code 02, Sub-
Field 4. Refer to Station
Configuration,
Section
710.2
for the complete
programming
proce-
dures to enable Preferred
Line Answer
(PIAl for
the SL4 station
ports.
B.
CORin@ng
Direct
CO rir@ng
is allowed
to a SL4 device.
Ringing
assignments
may be for day ringfng
and/or
night
ringing.
Ringing
assignments
are programmed
in the Station
Configuration,
CO Ringing,
program
code 13 and 14. Refer to
Section 720.3 and 720.4 for complete
program-
ming
procedures
for entering
CO ringing
as-
signments.
If the
SLA is programmed
to
receive incoming
ringing
for more than one line
and the SLA is busy when
a CO line rings in,
no signal will be presented
to the SLT.
Issue
1, January
1992
730-Z
Advertisement
Table of Contents
